Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Philips | FL4.16 | Correction to service information FL 95.01 | Correction to service information FL 95.01 ------------------------------------------ Correction in the overview of 100Hz and Proscan boxen. The replacement for service code 4822 212 30534 must be 4822 212 31231 The replacement for service code 4822 21 | ||
Philips | FL4.16 | Correction to service information FL 95.01 | Correction to service information FL 95.01 ------------------------------------------ Correction in the overview of 100Hz and Proscan boxen. The replacement for service code 4822 212 30534 must be 4822 212 31231 The replacement for service code 4822 21 | ||
Philips | FL4.16 | Both languages can be heard by Dual Nicam signals | For FL1-PTV change the software into V89; 4822 900 10732 For all other FL sets change the software into V88; 4822 900 10723 REMARKS :Introduced in production from week 9614 onwards. | ||
Philips | FL4.16 | Blank picture. OSD not synchronised and too large, no TXT. | Check/replace memory IC 7900 (ST24C08CB1; 4822 209 32283). | ||
Philips | FL4.16 | Bad picture. Picture scrolls. No RC reaction. | +5V was 4,1V instead of 5,1V. Replace IC7551 (LM358N; 4822 209 70672) | ||
Philips | FL4.16 | Bad pict. No menu. Dark bars over pict. Red pict. in dig.scan mode. | +5V was 4,3V instead of 5,1V. IC7551 (LM358N 4822 209 70672) defective. IC7209 (SAA7158 4822 209 31059) Bendic defective. | ||
Philips | FL4.16 | Bad focus or focus varies in a new set or after CRT replacement | Possible solution: Short circuit the focus and the G2 pins of the picture tube with the aquadag coating. Switch the set on for approximately 5 seconds. After this return the set to its original condition. Check if the focus adjusted normally. If not repla | ||
Philips | FL4.16 | "NVM write protection enabled" message on screen. | Startup problem or 'NVM write protection enabled' message on screen after replacement of NVM (ST24C08CB1; 4822 209 32283) with a ST24C08CB6 (4822 209 33113). Use as replacement the ST24C08 1 (9311 021 36682). | ||
Philips | FL2G | Pix folded at the bottom | Change capacitor 2652 (1000 mF/50 volts). 2652 is filter cap for -14v supply. | ||
Philips | FL2G | No picture or blue mute when other equipment is used in search mode | Disable the blue mute by changing the option code. Decrease the original value with one. | ||
Philips | FL2G | High failure of PTC | For main input 100V: Change position 3020 and 3021 on the Large Signal Panel into 4822 116 40277 For main multi voltage: Change position 3020 and 3021 on the Large Signal Panel into 4822 116 40247 REMARKS : Introduced in production in week 9550 | ||
Philips | FL2G | Dark pix. No luminance (Y) signal. | Cap 2327 (100nF) on SSP between pin 15 of IC 7324 (TDA4670) and ground leaky. No `Y' output from TDA4670. Replace 2327. | ||
Philips | FL2G | Bad focus or focus varies in a new set or after CRT replacement | Possible solution: Short circuit the focus and the G2 pins of the picture tube with the aquadag coating. Switch the set on for approximately 5 seconds. After this return the set to its original condition. Check if the focus adjusted normally. If not repla | ||
Philips | FL2.30 | off | lop tr & FET7480 leaky - fit line repair kit | ||
Philips | FL2.3 | off with whistling | line sw FET s/c & low res across lop - C2433 510nf s/c |