Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Philips | FL1.20 | Low Brightness TXT and OSD, Picture OK | If this condition occurs, check the Option Codes. Resetting the Option Code numbers as per the Service Manual provided the cure. | ||
Philips | FL1.20 | Four dark bars over the picture. | The +5 volt was 5.6 volt instead of 5.1 volt. Check/replace IC7551 (4822 209 70672). | ||
Philips | FL1.20 | Dark picture, only green led, no menu or OSD. | +5V supply was 4,1V. Voltage D6551 was 4,3V instead of 5,6V. Check/replace D6551 (4822 130 80954). | ||
Philips | FL1.20 | Correction to service information FL 95.01 | Correction to service information FL 95.01 ------------------------------------------ Correction in the overview of 100Hz and Proscan boxen. The replacement for service code 4822 212 30534 must be 4822 212 31231 The replacement for service code 4822 21 | ||
Philips | FL1.20 | Correction to Product Survey 1996-4 | Correction to Product Survey 1996-4 (4822 727 21505) ---------------------------------------------------- On page PCS 41989 is mentioned at: FL1.10 AG11 and higher: Control panel 4822 212 31708 FL1.17 AG20 : Control panel 4822 212 31708 FL | ||
Philips | FL1.20 | Both languages can be heard by Dual Nicam signals | For FL1-PTV change the software into V89; 4822 900 10732 For all other FL sets change the software into V88; 4822 900 10723 REMARKS :Introduced in production from week 9614 onwards. | ||
Philips | FL1.20 | Blank picture. OSD not synchronised and too large, no TXT. | Check/replace memory IC 7900 (ST24C08CB1; 4822 209 32283). | ||
Philips | FL1.20 | Bad picture. Picture scrolls. No RC reaction. | +5V was 4,1V instead of 5,1V. Replace IC7551 (LM358N; 4822 209 70672) | ||
Philips | FL1.20 | Bad pict. No menu. Dark bars over pict. Red pict. in dig.scan mode. | +5V was 4,3V instead of 5,1V. IC7551 (LM358N 4822 209 70672) defective. IC7209 (SAA7158 4822 209 31059) Bendic defective. | ||
Philips | FL1.20 | Bad focus or focus varies in a new set or after CRT replacement | Possible solution: Short circuit the focus and the G2 pins of the picture tube with the aquadag coating. Switch the set on for approximately 5 seconds. After this return the set to its original condition. Check if the focus adjusted normally. If not repla | ||
Philips | FL1.2 28ML8762/05B | Narrow pic & goes off | 9n1 tuning cap in psu | ||
Philips | FL1.2 28ML8762/05B | Fails to start with error code "99" | Try changing chopper Tr to 2SC3973B (BUT11AF) | ||
Philips | FL1.2 | Wrong synchronization, unstable colors | D6417 on the LSP dependent on temperature, check/replace (4822 130 81223) | ||
Philips | FL1.2 | Wrong service batch of ST24C08CB1 memory IC's 4822 | Wrong service batch of ST24C08CB1 memory IC's 4822 209 32283 ------------------------------------------------------------ Temporarily a wrong batch of EAROM's has been delivered, causing the fault "NVM MEMORY NOT WRITE PROTECTED" after replacing the EAROM | ||
Philips | FL1.2 | With fast moving picture poor picture quality (scan effect visible) | Change software into version V52 or higher 4822 900 10337. REMARKS : With this software it is possible to switch off LFR. |