| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Philips | FL1.17 | Bad synchronization with external signals | Delete position 3115 on the ECO 100Hz box. REMARKS : Introduced in production in week 9415. | ||
| Philips | FL1.17 | Bad picture. Picture scrolls. No RC reaction. | +5V was 4,1V instead of 5,1V. Replace IC7551 (LM358N; 4822 209 70672) | ||
| Philips | FL1.17 | Bad pict. No menu. Dark bars over pict. Red pict. in dig.scan mode. | +5V was 4,3V instead of 5,1V. IC7551 (LM358N 4822 209 70672) defective. IC7209 (SAA7158 4822 209 31059) Bendic defective. | ||
| Philips | FL1.17 | Bad focus or focus varies in a new set or after CRT replacement | Possible solution: Short circuit the focus and the G2 pins of the picture tube with the aquadag coating. Switch the set on for approximately 5 seconds. After this return the set to its original condition. Check if the focus adjusted normally. If not repla | ||
| Philips | FL1.17 | Antenna input: no sound. External input: sound O.K. | Check whether crystal 1602 (stereo decoder) 10MHz oscillates. If not replace X1602 (4822 242 80276). | ||
| Philips | FL1.17 | After about 10 min. cracking noise from the right tweeter. | Cracking signal from pin 6 of IC7009 (LM833N) on LSP (4822 209 83163) | ||
| Philips | FL1.17 | After 10 minutes picture becomes red from right side | C2395 on the LSP poorly soldered. | ||
| Philips | FL1.17 | Adaption of Service Information FL93.05 | Adaption of Service Information FL93.05 --------------------------------------- From 93-06-24 onwards the definition of optioncode 4 has been changed. From this day onwards the definition is as follows: 1 TXT peaking filter on/off for LFR box (Scandina | ||
| Philips | FL1.17 | 50Hz buzz noticable through speaker | Check/replace IC7680 on the SSP - TDA8425, pseudo stereo IC. (4822 209 63734). | ||
| Philips | FL1.17 | 22AV1440 is switched on by external VCR when FL1 is switched off | Connect 4 diodes of type BAT 85 to inputs of IC7630 on SSP. 1 diode between pin 3/IC7630 and +5V, cathode to +5V. 1 diode between pin 5/IC7630 and +5V, cathode to +5V. 1 diode between pin 3/IC7630 and -8V, anode to -8V. 1 diode between pin 5/IC7630 and -8 | ||
| Philips | FL1.17 | 100Hz cross | Possible solutions: 1. Interrupt on the SSP the 50Hz Y-signal, between pin 11 position IC7324 (TDA4568) and pin 11 position IC7395 (TDA8443), by deleting position 4302. Repair the connection by means of a shielded cable of 16cm long, m | ||
| Philips | FL1.17 | "NVM write protection enabled" message on screen. | Startup problem or 'NVM write protection enabled' message on screen after replacement of NVM (ST24C08CB1; 4822 209 32283) with a ST24C08CB6 (4822 209 33113). Use as replacement the ST24C08 1 (9311 021 36682). | ||
| Philips | FL1.16 | Wrong synchronization, unstable colors | D6417 on the LSP dependent on temperature, check/replace (4822 130 81223) | ||
| Philips | FL1.16 | Wrong service batch of ST24C08CB1 memory IC's | Wrong service batch of ST24C08CB1 memory IC's 4822 209 32283 ------------------------------------------------------------ Temporarily a wrong batch of EAROM's has been delivered, causing the fault "NVM MEMORY NOT WRITE PROTECTED" after replacing the EAROM | ||
| Philips | FL1.16 | Various faults can be observed. | Check the earth connection from the SSP: connect earth tuner with earth line output transformer (LSP) to find-out whether the problem is solved. Check connectors L02 and S02 pins 1,2 (sometimes only 7 wires are used in the connector) |