| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Philips | FL1.1 | LEDs blinking; error code 99. | Check C2504, across collector and emittor of TS7504 and/or TS7506, on the LSP and replace and/or it by a 3kV version. 820p 3kV 10%: 4822 126 13152 1n 3kV 10%: 4822 126 13153 1n2 3kV 10%: 4822 126 13154 1n5 3kV 10%: 4822 126 13 | ||
| Philips | FL1.1 | Jitter | In PIP unit change the value of R3336 to 4k7. | ||
| Philips | FL1.1 | Int startup/reverts to st/by | R3374 75k ¼w o/c | ||
| Philips | FL1.1 | How to enable/disable "Child Lock" | Press "MENU" button on Remote Control. When the menu appears on the screen, you select "SPECIAL FEATURES" (this expression is language dependent) Within "SPECIAL FEATURES", the "CHILD LOCK" can be enabled or disabled. | ||
| Philips | FL1.1 | Horizontal black lines with 100Hz sets and Sony Hi8 camcorders. | Change the value of C2396 on the small signal into 220nF (4822 122 32927). On 100Hz sets together with the Sony Hi8 camcorders, you can see very small sharp lines over the picture. This phenomenon is most of the times visable when the tape is situated i | ||
| Philips | FL1.1 | Horizontal amplitude cannot be adjusted | Transistor 7610 (2SA1359) on the LSP short circuited, check/replace. (4822 130 60111). | ||
| Philips | FL1.1 | Green fly-back lines, interrupts | C2451 (330nF; 5322 121 42661) on pin 17 of IC7430 (TDA4680) defective . | ||
| Philips | FL1.1 | Green and red coloured stripes visible in picture. | Check/replace IC7253 on the High End Box (SDA9060; 4822 209 63891). | ||
| Philips | FL1.1 | Frontends FQ816ME/B and FQ816MF/IF | Frontends FQ816ME/B and FQ816MF/IF ---------------------------------- 1. For the frontend with service code number 4822 210 10507 the following types can be supplied: FQ816ME/B with factory code number 3122 297 10901 FQ916DME/SERVICE with factory | ||
| Philips | FL1.1 | Field foldover | Check zener 6451 3v6 or 5v6 | ||
| Philips | FL1.1 | Fall off position 3204 on the Large signal panel | Fall off position 3204 on the Large signal panel ------------------------------------------------ When position 3204 (NTC/PTC; 4822 116 40215) on the LSP is defect it is recommended to replace it by a PTC/PTC (4822 116 40253). Together with this change al | ||
| Philips | FL1.1 | E/W fault - bowed sides. | TS7542 and TS7540 short circuit. REMARKS : There is a mistake in the Service Manual. TS7542 is drawn as a PNP type, but the transistor type should be BC857C as indicated in the spare parts list. The correct transistor is given in the parts l | ||
| Philips | FL1.1 | Drifting picture due to no sync. | Fault occurs after one hour. Before assuming line oscillator problem, try freezing the components in the high end box. If this clears the problem, check IC7203 - TDA 2579B (4822 209 63423) on the LFR (digital scan) box. REMARKS : The ICs TD | ||
| Philips | FL1.1 | Drifting picture due to no sync. | Fault occurs after one hour. Before assuming line oscillator problem, try freezing the components in the high end box. If this clears the problem, check IC7203 - TDA 2579B (4822 209 63423) on the LFR (digital scan) box. REMARKS : The ICs TD | ||
| Philips | FL1.1 | Does spontaneously switch over to program 1. | Check resistor value of R3250 (in standby SOPS circuit). Maximum value 62 Ohm (4822 116 52198). |