| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Philips | FL1.0 | Spook in picture | Use special antenna cables. Codenumbers: 4822 321 61224 PAL 1 meter 4822 321 61225 PAL 2 meter 4822 321 61226 SECAM 1 meter 4822 321 61227 SECAM 2 meter | ||
| Philips | FL1.0 | Sound distortion. Voltage pin 4 IC7635-2B too low. | Check D6172 (LLZ-C7V5; 4822 130 80906) on the SSP for -8 supply voltage. | ||
| Philips | FL1.0 | Sometimes set switched back to standby. Only red LED on. | Microprocessor panel defective (4822 212 30502 and 4822 900 10331) | ||
| Philips | FL1.0 | Sometimes no picture only sound. | Check pin 3 from connector D14 (Blue input). | ||
| Philips | FL1.0 | Sometimes in protection, or hor. width varies | Check or resolder on LSP the pins of E/W bridge coil 5521. | ||
| Philips | FL1.0 | Set switches off by hardware protection from sound. Error code 99. | Check Audio IC7000 on LSP (4822 209 73311; TDA1521Q). | ||
| Philips | FL1.0 | Set shuts down. | T7542 leaky. | ||
| Philips | FL1.0 | Set in stand-by mode, cannot be switched-on with remote control. | Check diode D6522 (BDY228/20; 4822 130 41275) and transistor T7610 (BD948F; 4822 130 60935). | ||
| Philips | FL1.0 | Set can only be operated with Remote Control | Check whether "Child Lock" is disabled. To check this, see "Frequently Asked Questions", "How to disable Child Lock". | ||
| Philips | FL1.0 | Service manual corrections; remote control battery | Service manual corrections; remote control battery lid ------------------------------------------------------ In the service (model) manual the battery lid (cover) for the RC6411 and RC6412 is supplied without the metal battery contact. Code numbers for | ||
| Philips | FL1.0 | Service manual correction TS7005, TS7006 | Service manual correction TS7005, TS7006 ---------------------------------------- In chassis manuals for the FL1.0, FL1.1, FL1.6 and FL1.7AA transistors TS7005 (BC848C) and TS7006 (BC848C) in diagram G are drawn incorrectly. They should be drawn with coll | ||
| Philips | FL1.0 | SAT box TXT | SAT box TXT ----------- Modification: item 3333 added 4822 116 52284 (47k) Remark: mounted between pin 11 of IC7330 and L5350. Reason: pull-up resistor needed for D2sync of the TPU (TPU error) Production intro date: week 9234. | ||
| Philips | FL1.0 | Production modification TDA4680 supply | Production modification TDA4680 supply -------------------------------------- Jumper 9481 is replaced with a diode type BAT85 4822 130 31983 cathode to pin 5 of IC7430, TDA4680 on the SSP. REMARKS : Introduced production in week 9228. | ||
| Philips | FL1.0 | Problems due to CNX83X | Change into CNY17-3.6 (4822 130 83177) REMARKS : Production intro date: 92-06-18 | ||
| Philips | FL1.0 | PIP picture not in order. | Check R3345 (4822 111 41424) in PIP unit, check IC7755 (4822 209 63423). |