Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Philips | ANUBIS-S | Powers supply output voltages for the different sc | Powers supply output voltages for the different screensizes for ANUBIS-S AA/BB/CC/DD ------------------------ For adjusting the power supply output voltage (via R3512) following survey gives an overview of the values for the different screensizes of all c | ||
Philips | ANUBIS-S | Plop sound at switch off of the set | For mono versions: Replace D6109 by BZX79-C2V7 (5322 130 34563) For stereo PB (+ BTSC) versions: Replace D6807 and D6808 by LLZ-C2V7 (4822 130 81138) REMARKS : Introduced in production week 9331 | ||
Philips | ANUBIS-S | Plop at switching on/off NICAM sound | In case of a NICAM switch on/off plop it is recommended to change on the NICAM module (diagram K) of the Anubis S BB: * Place elco 47uF 20% 25V (4822 124 40433) with + to pin 9 of IC7075 and with - to ground * Replace C2065 and C2076 by 470nF 10% 50V ( | ||
Philips | ANUBIS-S | Plop at switching on/off NICAM sound | In case of a NICAM switch on/off plop it is recommended to change on the NICAM module (diagram K) of the Anubis S BB: * Place elco 47uF 20% 25V (4822 124 40433) with + to pin 9 of IC7075 and with - to ground * Replace C2065 and C2076 by 470nF 10% 50V ( | ||
Philips | ANUBIS-S | Pix blanks at certain prog. nrs | Software bug. Micro Processor need to be replaced. Change from version SA FHV 1.9 to SA FHV 2.1 | ||
Philips | ANUBIS-S | Picture width too small during off-air reception. | Delete R3453, R3454 and L5454 in the line defl flyback circuitry and place jumper at position 9454. REMARKS : Introduced in production week 9340 in Spore and week 9346 in LFL Thailand. | ||
Philips | ANUBIS-S | Picture tube 20" Anubis S AA and CC A48KXR98X | Picture tube 20" Anubis S AA and CC A48KXR98X (4822 131 20577) --------------------------------------------------------------- Only for ANUBIS-S 20" AA and CC For both Anubis S AA and CC picture tube A48KXR98X (neutral hemisphere) is no longer available | ||
Philips | ANUBIS-S | Picture jittering when OSD is recalled, all versions | Replace R3605 by 2k (4822 116 52253) at pin 20 of uP REMARKS : Introduced in production week 9328 | ||
Philips | ANUBIS-S | OSD characters too thin | It is recommended to replace in the control part: R3715 by 1k2 (4822 116 52207) REMARKS : Introduced in production week 9408 | ||
Philips | ANUBIS-S | Only for ANUBIS-S BB 25" Codenumber information | Only for ANUBIS-S BB 25" Codenumber information ---------------------- The missing service codenumber for the bridge coil L5480 in the east / west part of the 25" ANUBIS S BB (diagram AA) is: 4822 157 71149 | ||
Philips | ANUBIS-S | Only for ANUBIS-S BB 25 Adaption in the frame par | Only for ANUBIS-S BB 25 Adaption in the frame part of 25" Anubis S BB --------------------------------------------- From production start onwards the following modification is done in the convergence circuitry in the frame part of diagram AA: R3403 shou | ||
Philips | ANUBIS-S | One colour missing or no picture | In case of 1 colour missing or no picture, it is recommended to solder across R3301 on the CRT panel on the copper side: 100nF 10% 250V 4822 121 41689 This capacitor protects the 3 BF422 video output transistors TS7305, 7318 and 7327 against flash REM | ||
Philips | ANUBIS-S | No stereo, no +95 volt | R3523 is interrupted, D6519 and C2519 (= capacitor between D and S-7513) are short circuited. Remove C2519. Replace R3523 - 390K - 4822 116 52278 Replace D6519 - BTZ03-C15 - 5322 130 31574 | ||
Philips | ANUBIS-S | No picture after picture tube flash over | In case after a picture tube flash over (one of) the video output transistor(s) BF422 (TS7305, TS7318, TS7327) failed, it is recommended to: 1. Change 2337 to 4n7 2kV 4822 126 12833 2. Delete and short R3336 with a wire jumper 3 | ||
Philips | ANUBIS-S | No picture | Apply a slight force to further insert the EHT cable into the line output transformer 5445. REMARKS : Above cure is only relevant for sets with LOT 4822 140 10525 or 4822 140 10557. When replacing the above mentioned LOT's, please take note of t |