| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Philips | ANUBIS-S | No NICAM sound | In case of no NICAM sound it is recommended to replace on the NICAM panel: R3055 to 560 ohm 2% 0.25W 4822 051 10561 (diagram K page 21 in the service manual Anubis S BB 4822 727 20262) REMARKS : Lower R3055 gives a higher starting current fo | ||
| Philips | ANUBIS-S | No colour at PAL in case of disconnected 2CS+I/O+Ampl panel | In the service position, the main panel of the Anubis S BB is disconnected from the 2CS+I/O+Amplifiaction panel. For Anubis S BB sets with 2 HEF shift register in cascade (as how it is used by now for controlling an Anubis S BB set with incredible stere | ||
| Philips | ANUBIS-S | No +95V/+115V from power supply | In case of a failure of one of the components TS7513, R3503 or D6502 till D6505, it is strongly recommended to replace all of these components. For service codes see, Service Manual ANUBIS-S AA GB 4822 727 19707 E 4822 727 19719 ANUBIS-S BB | ||
| Philips | ANUBIS-S | Modification | Modification ------------ For ALL ANUBIS-S WITH NO SECAM RECEPTION IC7225 TDA8362 is replaced by TDA8361 in all ANUBIS-S sets with no SECAM reception possibility from production week 9416 onwards, so, IC7225 = TDA 8361E/N3 4822 209 33479 (PAL + NTSC, n | ||
| Philips | ANUBIS-S | Mains fuse 1500 fails constantly | In case the mains fuse of a 25" Anubis S BB set constantly blows, it is recommended to upgrade it to a 4A type: Change fuse 1500 to T4A 4822 070 34002 Also update the text T3.15A on the service printing to a sticker with the text T4A. REMARKS | ||
| Philips | ANUBIS-S | Lock-up problem during program change; error message 6 & 7 on screen | Change R3198 into 560E - 4822 051 10561 REMARKS : Problem behaviour: After pressing first digit, first digit appear on the screen. No further digit can be inserted. The program will stay as previous selected. The digit will disappear after 30-45 | ||
| Philips | ANUBIS-S | Line output transformer 4822 140 10486 is no longe | Line output transformer 4822 140 10486 is no longer available ------------------------------------------------------------- Only for 21" Anubis S BB/14" Anubis S CC LOT 4822 140 10557 can be used as a substitute. However C2450 has to be changed from 560n | ||
| Philips | ANUBIS-S | Line output failure | Check line transistor TS7445 (4822 130 60851) If TS7445 defective, by then also replace C2445 by 680 pF 2kV 4822 126 12269 C2446 by 5n6 2kV 4822 121 70355 C2447 by 680 pF 2kV 4822 126 12269 REMARKS : Introduced in production week 9323 | ||
| Philips | ANUBIS-S | Interference in Band I | a. For all 14" sets and 20"/75/79 and 21"/75/79 sets replace uP IC7600 by PCA84C844P/110 (4822 209 32927) b. For all 14-20-21" sets add bead (4822 526 10606) between anode of D6530 and D6531 (at the secondary side of the FFS transfor | ||
| Philips | ANUBIS-S | INSTALL or STORE not possible; sound volume might be too low | Check whether "Hotel Mode" is disabled. To check this, see "Frequently Asked Questions", "How to de-activate "Hotel Mode". | ||
| Philips | ANUBIS-S | IC7225 does not start up. | Solder 3 x BAT85 (4822 130 31983) on copper side of the main carrier. Cathode pin 41 IC7225 anode ground Cathode pin 43 IC7225 anode ground Cathode pin 36 IC7225 anode ground Make bare ends as short as possible and isolate with a sleeve REMARKS | ||
| Philips | ANUBIS-S | How to de-activate "Hotel mode" | Applicable for family: PLL sets For DD sets Identification on uP: Hotel mode can only be de-activated if the software for hotel mode is available (so an "H" version) and when the hotel mode option (address 246) is enabled. Only 1 hotel mode is possible: | ||
| Philips | ANUBIS-S | How to de-activate "Hotel mode" | Applicable for family: VST sets For DD sets Identification on uP: Hotel mode can only be de-activated if the software for hotel mode is available (so an "H" version) and when the hotel mode option (address 246) is enabled. Two hotel modes are possible: | ||
| Philips | ANUBIS-S | How to de-activate "Hotel mode" | Applicable for family: PLL sets For AA/BB/CC sets Identification on uP: Hotel mode can only be de-activated if the software for hotel mode is available (so an "H" version) and when the hotel mode option (address 246) is enabled. Only one hotel modes is p | ||
| Philips | ANUBIS-S | How to de-activate "Hotel mode" | Applicable for family: VST sets For AA/BB/CC sets Identification on uP: Hotel mode can only be de-activated if the software for hotel mode is available (so an "H" version) and when the hotel mode option (address 246) is enabled. Two hotel modes are possi |