Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Philips | 14TVCR240 | No picture, but sound is OK. | Check the +25V supply. If this is not present, check resistor R3511. This resistor is mounted on the supply-PCB near the LOT. This resistor is specified by correct type only, as mentioned in the service manual. 12NC: 4822 052 11278 (2E70.5W safety). | ||
Philips | 14TVCR240 | No pic - sound ok | R8511 o/c; IC7510 TDA3653B f o/p chip u/s | ||
Philips | 14TVCR240 | Motor holder with reverse prism included | Cut part from the motor holder. REMARKS : For drawing see repair information PAL 96/09 (from 13.10.96) | ||
Philips | 14TVCR240 | Modification picture tube | From production week 9610 onwards, an ORION picture tube was mounted. The codenumber was 4822 131 11075. Together with this picture tube capacitor C2586 has been changed to 8 nF - 1600 V. Codenumber 4822 121 70629. For replacement ORION picture tube by | ||
Philips | 14TVCR240 | Memory erase procedure | The contents of the memory can only be cleared via the service mode. This option is not available for end users. (Risc of destroying option codes). Service mode: press "STOP" on Remote Control and "PLAY" on the set for 5 seconds. Select the second page | ||
Philips | 14TVCR240 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11069. Key set for: 14PV162/01/02/05/07/08/13/58 - 14PV170/05 - 14TVCR240/01N. | ||
Philips | 14TVCR240 | How to erase memory | Press simultanuously buttons REWIND, WIND and PROGRAMM (<<, >> and P-) while switching on the power supply. Note: Correct your service manual on page 1-1-11. The description in the Instruction For Use is correct. | ||
Philips | 14TVCR240 | Field collapse | TDA3653 replaced | ||
Philips | 14TVCR240 | dead, PSU not running | D6334 UG06B leaky (482213083307) | ||
Philips | 14TVCR240 | Dead with blurting noise | LOPTx s/c CHS code no P81397 | ||
Philips | 14TVCR240 | Dead | D6581 - used By133 in lieu | ||
Philips | 14TVCR240 | Dead | Check start up volts pin 6 TDA4605 should be 10v; if low at 3v check UG06B diode D6334 for leak (pt no 4822 130 83307) | ||
Philips | 14TVCR240 | Damages tapes; eject of cassette with difficulty. | Replace kit I (4822 310 31963). | ||
Philips | 14TVCR240 | Correction partslist | In the partslist, 17.734 MHz is mentioned for X-tal pos.1200. This has to be 4.43 MHz. The codenumber 4822 242 81809 is correct. Also the specifications of the X-tal on the circuit diagramm on page 1-3-7 is correct. | ||
Philips | 14TVCR240 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271. This new version is only used in the following sets: 14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05, 14PV163/05H, 14PV263/01, |