Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Philips | 14PV162/05 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271. This new version is only used in the following sets: 14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05, 14PV163/05H, 14PV263/01 | ||
Philips | 14PV162/02 | Option code: 00972 | From week 02/97 onwards the option code is printed on the typesticker. Always use this code ! For early sets without this information on the typesticker, the option code is: 00972 | ||
Philips | 14PV162/02 | New VPS IC SDA5642-6 (pos. 7840) | Since production week 9741 a new VPS IC pos. 7840 (SDA5642-6) is introduced in production. This IC is not compatible with the previous one. When ordering, look at the printing on the IC ! Old: SDA 5642-5 - codenumber 4822 209 32728 New: SDA 5642-6 - | ||
Philips | 14PV162/01 | Option code: 00396 | From week 02/97 onwards the option code is printed on the typesticker. Always use this code ! For early sets without this information on the typesticker, the option code is: 00396 | ||
Philips | 14PV162/01 | Codenumber information | A new software version (PTCP2-7) is available for the control uP (IC 7801). Service codenumber is 4822 209 15271. This new version is only used in the following sets: 14PV263/01, 14PV162/01, 14PV162/05, 14PV162/07, 14PV163/05, 14PV163/05H, 14PV263/01 | ||
Philips | 14PV162 | Tuner modification | An early production problem appears on these sets: the AGC voltage supplied to the Tuner 1 is too high (app. 8.8V) in comparison to the supply voltage (5V). It results in a wrong correction of the AGC loop when the antenna's signal is too low (about 1,5mV | ||
Philips | 14PV162 | Start up problems | When the set is switched on by the mains-switch while a cassette is in the set, the front LED starts blinking, but the set doesn't start. Solution: Check the primary voltage (Ubat) and adjust this for 14" sets to exactly 101.5 Volt. (See chapter 3.1.1 | ||
Philips | 14PV162 | Spare part information | If the lever inside the mains-switch is broken, the switch doesn't remain in the "ON" position. Solution: replace the switch by a new one. Improved switches of a newer production range are on stock. (4822 276 13542) | ||
Philips | 14PV162 | Spare part information | A repair kit , containing PULLEY SHAFT + WORM SHAFT (POS. 47+48) is delivered with codenumber 4822 310 10657. This kit can be used for all TURBO- and ECO mechanisms ! | ||
Philips | 14PV162 | Set produces audible noise in stand-by | Add a small LEBL (leading edge blanking) PCB, to avoid auto oscillation of transformer 5330 (or 5331). A modification letter is included with the lable PCB. This PCB is available with service nr. 4822 214 12173. Since production week 9723 this circuit is | ||
Philips | 14PV162 | Preventive tip | If FET 7352 is found to be defective, it is advised to mount a 15 V zenerdiode (BZX79-C15) between the drain and the gate. Mount cathode to gate and anode to drain. Codenumbers: FET 7352: 4822 130 60838 ZENER (BZX79-C15): 4822 13034281 Introduc | ||
Philips | 14PV162 | Modification | From week 9644 onwards, the following modifications are done on the Small Signal Board: 2076 / 470pF 5% is DELETED. 3075 / 33k 5% is DELETED. 4999 / CHIP JUMPER / 4822 051 20008 is inserted in place of 2076. The RC differentiator was not necessary whe | ||
Philips | 14PV162 | Memory erase procedure | The contents of the memory can only be cleared via the service mode. This option is not available for end users. (Risc of destroying option codes). Service mode: press "STOP" on Remote Control and "PLAY" on the set for 5 seconds. Select the second page | ||
Philips | 14PV162 | Key set | The key set assy has been codified for all B-range TVCR's. This will allow to change the keys without having to change the complete frame. Servicenr. 4822 410 11069 - Key set for: 14PV162/01/02/05/07/08/13/58 - 14PV170/05 - 14TVCR240/01N. | ||
Philips | 14PV162 | Codenumber information | The codenumber for the spacer between on/off switch and the knob (pos 3) is 4822 402 10702. |