Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por:![]() |
---|---|---|---|---|---|
Sony | D131 | INTERMITTENTLY READS NO DISK - RESOLDERED IC801 | Unit would not read discs. I put pressure on door open/closeswitch and unit would function correctly. | ||
Sony | D131 | INABILITY TO READ DISCS - REPLACE IC501, P/N 8-752-063-45 | Unit sent in with C file but no explanation of problem.Found unit skips. Changed optic block but it continued to skip and thennot play. | ||
Sony | D131 | DIFFERENT MAIN BOARD | The main board in this unit does not match the manual or anyof the suppliments. The P/N on the board is 165395511. Need schematic toT/S unit. -HQ COMMENTS: Contact Kansas City Parts, att'n: Jamie Lyon, phone #816-891-7550 ext 256, fax # 816-891-2580. | ||
Sony | D121 | NO POWER - RESOLDER HOLD SWITCH | Unit would not turn on. | ||
Sony | D111 | INABILILTY OF OPTICS TO MOVE | Customer complaint of making a clicking sound. Would notread a disc due to the inability of the optics to move toward innerlimit. This is a refurb unit. | ||
Sony | CFD758 | CONSTANT BUZZING - DEFECTIVE OUTPUT IC307 | Constant buzzing when unit was plugged in. When unit wasturned on, the buzzing got louder. | ||
Sony | CFD676 | AUDIO AND DISPLAY GO OUT - COLD SOLDER ON MCB | After unit warms up the audio & display backlight goes out.Found C373 had a cold solder joint on the negative side of the cap. Thereis a jumper wire from this cap to pin of IC306. The jumper wire wassoldered to the leg of the cap but not soldered pr | ||
Sony | CFD616 | INTERMITTENT CD JAMMING OR NOISE | Cust had complained of rubbing noises and occasional jammingof CDs in unit. After much dissassembly and checking, servicer found thatref#225 lever(T) was not meshing properly with ref#262 gear(L1). This wasdue to post on Chassis(sub) assy ref#263, being | ||
Sony | CFD616 | NO REF # FOR CD PLASTIC CHASSIS | Need part # for plastic chassis on pg 39 of sm. It is theplastic chassis that fits on top of chassis sub assemble #263. It doesn'tseem to be listed in the manual or supplement #1 issued for unit. -HQ COMMENTS: Contact Kansas City Parts, attn Jamie Ly | ||
Sony | CFD600 | CD JAMMED | CD's jammed in unit. Suspect unit is transported with a CDin the play/spindle location, then gets bounced around affecting theloading alignment. Cust then turns on unit and drive loads incorrectly.I have instructed cust not to transport unit with cd's | ||
Sony | CFD600 | DISK BASE MISSING STOPPER | Stopper is missing in new disk base. See attached copy.This can accidently cause the disk base to lock up. | ||
Sony | CFD600 | DISC DRAWER DOESN'T CLOSE SMOOTHLY | After replacement of disc base, drawer, found new part hitssomething as it closes which causes drawer to move upward and overobstruction. Since old drawer did not have this problem there must bea difference between old and new one. | ||
Sony | CFD600 | MECHANISM JAMS | CD mechanism jams. Several reports have been submittedregarding this problem. | ||
Sony | CFD600 | CD CHANGER MECH JAMMED | Received unit with CD jammed in changer. Removed CD's.Physically turned gear Ref 267 so elevator gear brought the case (ref269) all the way in the up position. Powered unit, the eliminator mechwent down and jammed. | ||
Sony | CFD600 | WHEN PLAY IS PRESSED, UNIT INDICATES TAKE OUT DISC | When all the discs are loaded and play is pressed, unitindicates: Take out disc on every disc you attempt to play, 4th unit withthis problem. |