Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por:![]() |
---|---|---|---|---|---|
Sony | CDPC505 | WARPED DISC TABLE | Selecting a disk, disk would stop before centering under laserassembly. Problem was very intermittent. Frank in San Diego resolved theproblem. | ||
Sony | TCDD3 | MODE GEAR D SLIPS TOOTH | To Tokyo: It has come to our attention that Mode gear D isneeded as a replacement part. Due to the softer material this gears teethdeform and cause the other gears E and C to slip. This slippagecauses mechanical timing problems. We await your reply. F | ||
Sony | CPD1304 | POWERS UP BUT NO DISPLAY | Powers up but no display and no high voltage. Noise lookslike bad flyback transformer and sounds like flyback internal arching.Voltage check reveals no voltage going to collector of Q-403 HOT. It re-veals voltage is coming from Q-401 checking voltage o | ||
Sony | CFD770 | POWER DOES NOT COME ON WHEN PUSHING POWER SWITCH | Power will not come on when first pushing Power switch, if itdoes come on, unplug power cord for a couple of seconds and it will notcome on when pushed. | ||
Sony | CFD454 | HEADBASE SHOWN IN SERVICE MANUAL DOES NOT MATCH ACTUAL PART | Headbase shown in the service manual does not match the ac-tual part in unit. Part is shown with alignment posts and hold downclips. Part in unit has screw holes and a rear post. Verified with twoother CFD-454s in shop. No info in SDIS or any service | ||
Sony | STRAV19 | FRONT PANEL AVAILABILITY | There are 92 units at NRC awaiting front panels. Thereare 70 more units to be checked. There are 127 front panels on backorderin KCP. According to KCP front panel production has stopped for this unitand the parts may never be available. -HQ COMMENTS: | ||
Sony | CCDV101 | MANUAL IRIS PROBLEMS WHEN THE BOARD IS REPLACED | After replacing the VC-67 board, the manual iris wouldfunction normally until the last point where the iris should be closed.At this point the iris would fully open. | ||
Sony | D180K | UNIT DOES NOT FOCUS, FLEX CABLE HAS OPEN CIRCUIT | Unit does not focus (flex cable has open trace). Movement ofthe optical assembly puts stress on the flex cable causing it to break.This is the second unit with this problem. | ||
Sony | ITA305 | UNIT WON'T RESET | Customer says the unit won't reset. Pushing the reset buttonhas no effect. | ||
Sony | ICB1000 | SERVICE MANUAL IS INCORRECT - REFERENCE NUMBERS 14 AND 15 | Illustrations on page 7 are wrong. No. 14 and 15 should bereversed. Then part numbers will be correct. -HQ COMMENTS: Thanks for the info. The descriptions vs part numbers inthe service manual are correct. But as you mentioned, the referencenumbers 1 | ||
Sony | CFD460 | WON'T READ TOC | We have seen several units now where the disc spins, but willnot read TOC. There is often an audible clicking sound coming from themechanism. The problem is caused by the laser assembly binding with thechassis holder (No. 156). To verify the problem: | ||
Sony | SPP65 | PART NUMBER OF BATTERY | The part number of the handset's battery is not listed in theservice manual. -HQ COMMENTS: The battery is stocked at KCPS under the part numberBPT16. Therefore, please use this part number when ordering thebattery. A service bulletin will be issued. | ||
Sony | SPP55 | PART NUMBER OF BATTERY | The part number of the handset's battery is not listed in theservice manual. -HQ COMMENTS: The battery is stocked at KCPS under the part numberBPT16. Therefore, please use this part number when ordering thebattery. A service bulletin will be issued. | ||
Sony | BM815 | PH-901, 902 NOT LISTED IN SERVICE MANUAL | On page 25 of the BM-815 service manual it shows parts 907 and909 which correspond to 907 and 908 in the parts list: PHOTO INTERRUPTORPC BOARDS (S. REEL AND T. REEL). The part numbers are 1-619-136-11 and1-620-431-11. These part numbers are for boards | ||
Sony | SPP115 | TEST MODE PROCEDURES FOR BASE UNIT | The procedures for putting the base unit in test mode areunclear in the service manual. -HQ COMMENTS: The correct procedures for putting the base unit in testmode are as follows:1. Disconnect battery pack. 2. Unplug AC Adaptor. 3. Connect IC-501/pin 11t |