Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por:![]() |
---|---|---|---|---|---|
Sony | CFSW501 | PULLEY ASSEMBLY MOTOR WON'T FIT | Unit had bad wow and flutter on (B) deck. Found problem to bebreaking pulley (which is plastic). The replacement is brass and will notgo into shaft of motor. | ||
Sony | TCK950ES | UNIT EATS TAPE, TAKE-UP REEL INOPERATIVE | Take-up reel is intermittent. Same for FF and Rew operation.Unit eats tapes. Found problem on a few of these units. | ||
Sony | CDPC7ESD | NEED PART NUMBER FOR FRAME | No part number is listed in the service manual for frame. -HQ COMMENTS: A service bulletin was issued on July 25, 1989. It isHi-Fi #078. P/N for the frame is 4-924-407-06. A plastic pin whichretains the one of the table drive gears is missing on the | ||
Sony | CDPC70 | NEED PART NUMBER FOR FRAME | No part number is listed in the service manual for frame. -HQ COMMENTS: A service bulletin was issued on July 25, 1989. It isHi-Fi #078. P/N for the frame is 4-924-407-06. A plastic pin whichretains the one of the table drive gears is missing on the | ||
Sony | CDPC50 | NEED PART NUMBER FOR FRAME | No part number is listed in the service manual for frame. -HQ COMMENTS: A service bulletin was issued on July 25, 1989. It isHi-Fi #078. P/N for the frame is 4-924-407-06. A plastic pin whichretains the one of the table drive gears is missing on the | ||
Sony | CDPC40 | NEED PART NUMBER FOR FRAME | No part number is listed in the service manual for frame. -HQ COMMENTS: A service bulletin was issued on July 25, 1989. It isHi-Fi #078. P/N for the frame is 4-924-407-06. A plastic pin whichretains the one of the table drive gears is missing on the | ||
Sony | CDPC30 | NEED PART NUMBER FOR FRAME | No part number is listed in the service manual for frame. -HQ COMMENTS: A service bulletin was issued on July 25, 1989. It isHi-Fi #078. P/N for the frame is 4-924-407-06. A plastic pin whichretains the one of the table drive gears is missing on the | ||
Sony | CDPC20 | WIND SENSOR BOARD DIFFERENT STYLE THAN SHOWN IN S/M | The Wind Sensor Board sent to HQ by Boston Tech. Training isvery different from the Wind Sensor Board in the CDP-C20 Service ManualSupplement-1. The original board layout pictured in the S/M shows a 5-pinconnector CNJ1101, and IC1001. The board sent to H | ||
Sony | SSU930AV | PART NUMBER FOR PASSIVE RADIATOR INCORRECT IN S/M | The part number for the passive radiator listed in the SSU-930A/V service manual is incorrect (1-549-122-11). -HQ COMMENTS: The correct part number is 1-544-122-11. Use this numberwhen ordering a replacement part. | ||
Sony | CDPC401 | WIRE HARNESS IS TOO SHORT | Regarding service bulletin HFP0127, part number 1-946-072-21yields an eight-pin harness about four inches long, whereas this unitrequires a harness about twelve inches long. -HQ COMMENTS: Will fax Tokyo. To Tokyo: Should harness be longer? Isthere a l | ||
Sony | CDPC400 | WIRE HARNESS IS TOO SHORT | Regarding service bulletin HFP0127, part number 1-946-072-21yields an eight-pin harness about four inches long, whereas this unitrequires a harness about twelve inches long. -HQ COMMENTS: Will fax Tokyo. To Tokyo: Should harness be longer? Isthere a l | ||
Sony | EVS550 | NEED PART NUMBER FOR CASSETTE DOOR | I need the part for the cassette compartment door. It ismissing from the exploded view drawings and is not included with theloading mechanism of which it is a part. I have checked the list ofmiscellaneous parts with no luck. -HQ COMMENTS: The part num | ||
Sony | D9 | DISTORTION WITH AA BATTERIES ONLY | This D-9 would play fine with AC adaptor and BP-2rechargeable battery pack as supplied power, but the audio would bedistorted when using AA batteries. | ||
Sony | KV19TS20 | NO POWER ON WITH REMOTE, REPLACE Q-110 | Could not turn power on with remote. All other functions wereok including power off on manual or remote. IC-101 pin 5 was receivingproper data for power on. Pin 37 of IC-101 was low due to a leaky Q-110which provides AC reference. | ||
Sony | CCDTR7 | NO EJECT (FUSE BLOWS) | Camera came in replaced open PS-602 on VS-61 board. Every-thing seemed to work fine. Camera came back in. Same problem but theloading motor was frozen. |