Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | SLV676UC | INDEX | Went to a customer's home and he showed me a design problem.If you use a tape less in length than AT-120 and index 3 or 4 times with3 minute spacing, it will not stop until it sees the first index. Thisoccurs only in Reverse. Foward direction it stops | ||
Sony | ITD250 | MISSING PART NUMBER FOR BZ1 AND BZ2 | There are no part numbers for BZ-1 and BZ-2 in the servicemanual. -HQ COMMENTS: The 2 buzzers BZ1 and BZ2 are not available as separateitems. However they are part of the lower cabinet assembly.Therefore, if you need to replace BZ1 or BZ2, you will have | ||
Sony | KV5300 | HANDLE BRACKETS | Bracket which holds the handle is not shown or listed in theservice manual. Please let us know the part number. -HQ COMMENTS: Part number for the bracket is 4-361-411-01. | ||
Sony | CCDTR5 | INTERMITTENT POOR PICTURE QUALITY - NOISE IN PICTURE | Replace Q-107 in head assembly circuit. -HQ COMMENTS: Thanks for the information. Q107 is the Channel 1A RecordSwitch. | ||
Sony | CCDTR6 | WILL NOT LOAD, EJECT OR PLAY | No cap. vs from DD-31 board. | ||
Sony | EVS550 | NO OPERATION | No functions - display and LEDs flash. | ||
Sony | KV32XBR50 | NO PICTURE, ONLY CHARACTER DISPLAY, CHECK THE IK LINE | Sometimes at turn on the screen was black but would show theon screen display. Turning up G-2 revealed a barely visible rasterexhibiting extreme pincushion distortion. Also, three retrace lines at thetop of screen caused by improper data buss activity. | ||
Sony | CDP291 | INTERMITTENT STATIC IN AUDIO | Intermittent static in audio (especially in high frequency). | ||
Sony | KV2791R | SHUT DOWN, REPLACE R-507 | When the brightness and picture controls are high, Pin 6 ofIC-301 would drop to 2V, then the set would shut down. | ||
Sony | DTC300ES | NO DISPLAY | Minus 24 volt power supply fails. Gary in Costa Mesa showedme one that had all three components defective. -24 volts is lost whenQ-908 and Q-907 short, this I think causes C-915 to open. Gary says thisis the second unit he has had with this problem. | ||
Sony | KV27XBR15 | DEAD, REPLACED Q-503 AND REPAIRED COLD SOLDER JOINTS | Unit was dead, found shorted H output transistor andcold solder joints on H. Drive transformer. | ||
Sony | KV20EXR10 | LOW BRIGHTNESS, RESOLDERED R-741 ("C" BOARD) | Very low brightness. Looks like color only. RGB pulses arevery low. R-741 leads were not penetrating completely through the boardcausing misoperation of Q-711 thus sending a wrong IK pulse to pin 25 ofIC-301. | ||
Sony | STRD2020 | NO LEFT CHANNEL AUDIO | No left channel audio. Traced audio back to IC-307 still didnot have audio. Went to IC-301 pins 2 and 27 had audio. Thought IC-301or IC-307 had to be bad because the digital path was still sending rightchannel audio throughout digital 1 PCB until it b | ||
Sony | KV32HSR10 | SHUTS DOWN, "F" BOARD Q-651 E-B OPEN | Shut down. Found B+ 135V running between 136 and 142vdc. Iknew either the load was open or our B+ was not regulating. Removed the Fboard from the TV and jumped RY-601. I used a 60 watt lightbulb as my loadon the +135 volt line. Using the variac while mo | ||
Sony | CDPC201 | NEW SPINDLE MOTORS ARE BENT | Vertical jitter on RF waveform (eye pattern) after spindlemotor replacement. This is caused by a bent spindle shaft. There is nopacking material to protect the spindle shaft. Out of the last ten motorsreplaced, 6 were noticeably bent but could be used |