Dicas Reparação SONY
Modelo - Chassis
Pesquisa: SONY Enviar Dica Resolvida
Resultados 18945
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CCDTR5 | INTERMITTENT LOADING AND EJECT | Unit would not always eject and load properly. | ||
| Sony | TCWR808M | CASSETTE DECK - NO OPERATION | Reset pin of IC-401 was never going high to 5 volts. Thisline was followed back to Q-402 and Q-401 which were measured with a DVM.Q-402 base was .1Vdc, however, Q-402 appeared to be on. Measuring thebase of Q-402 with an oscilloscope showed approximate | ||
| Sony | E92F19B160 | NO PART NUMBER LISTED FOR FRONT PANEL - REFERENCE NO. 101 | There is no part number listed on page 35 of the S/M for thefront panel (Ref. No. 101). -HQ COMMENTS: From W. Janowski/C. Rashi (Detroit SSC): P/N is1-464-753-11. This part includes the panel, all the buttons, and thedisplay PCB. Although it seems as i | ||
| Sony | SCD1020S | MISSING PART NUMBER ON RECEIVER CABLE | Both TX and RX antenna cables at antenna end have a protectiveboot that covers the end connector. When these cables are supplied withproduct, there is no problem. However, when supplied thru NPC Parts,there is a missing retainer ring on the RX cable. | ||
| Sony | KV27TS20 | SAP NOT WORKING, ALIGNMENT? | I was contacted by a customer because SAP didn't work on hisunit (we have weather on Channel 6, the PBS channel here). He went to thestore and the display model didn't work either. I went to another storeand the display didn't work on SAP either. -HQ | ||
| Sony | CDX6020 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled into the unit. It may also not beejected. The disc is engaged with the roller, but the roller is slippingon the shaft. | ||
| Sony | CDXR79 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled into the unit. It may also not beejected. The disc is engaged with the roller, but the roller is slippingon the shaft. | ||
| Sony | CDXR77 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled into the unit. It may also not beejected. The disc is engaged with the roller, but the roller is slippingon the shaft. | ||
| Sony | CDXA30 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled out of the magazine. It will alsonot be pushed back in. The disc is engaged with the rollers, but theroller is slipping on the metal shaft. | ||
| Sony | BEV8 | ERRATIC FUNCTIONS | No Rewind, Forward or Eject. Eject mode could be activatedonly by pressing FF and Eject at the same time or REW and Eject. Microwould then produce scanning pulses. Noticed no change of voltage at Q-101to correspond with base voltage change when any fu | ||
| Sony | CCDF56 | VIEWFINDER CABINET PARTS COLOR | As you know, the CCDF55 and the CCDF56 have different colorsfor the cabinet parts. On page 104 of the service manual, it shows thepart numbers for the F55/F56 viewfinders, but no breakdown of the VFcabinet parts as shown in the accompanying diagram. Is | ||
| Sony | SLHF900 | INTERMITTENT CHROMA LOCK FLOATING VERTICAL COLOR BARS | In playback unit manifested vertical colored bars in picture.The actual video in the background was uncolored. Traced problem to anunlocked VCO on the VI-10 board. Tried adjusting RV-403, but noticed itwas erratic and the setting would drift with time | ||
| Sony | SPP120 | HOLD FUNCTION NOT OPERATIONAL | The hold function is not working. The unit disconnects withinone second after the hold button is pressed. | ||
| Sony | CFD454 | NO P/N FOR OPTICAL BLOCK CONNECTORS | The S/M does not list P/Ns for the connectors which connectthe FOP to the CD Main board into CN-701 and CN-709. | ||
| Sony | FD270 | PART NUMBER FOR SOCKET | Need the part number for the socket that the Flexible boardfits into located on the D-2 board. -HQ COMMENTS: Parts that you were looking for are: 1-566-539-11 Connector FPC 1-566-927-11 Housing ConnectorThese part |