Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por:![]() |
---|---|---|---|---|---|
Sony | KV32S20 AA-2 | uneven brightness | This product has a strange glow toward the top of the tube. Sort of an out of focus raster but only at the top 1/5 of the tube. | When raising the G2 voltage it was discovered the CRT had a uniform brightness where the top of the screen was brighter than the rest in the CRT. Measuring across the vertical yoke windings we found a8.5 volts. It should be ""0"" volts if the vertical output is working. It was also discovered the -15 was missing. Tech needs to look at D530 and R537 a 0.47 ohm resistor. Unit had bad diode, resistor and vertical output "" | Muller |
Sony | KV35V68 AA-2 | TV Guide Plus | TV guide plus does not function. When the television is setup for TV guide Plus the customer is selecting that they have a VCR and CATV box. But they are not using the Cable Mouse or IR Blaster. | The IR blaster is used to communicate from the television to the CATV box in order for downloading to occur. If the IR blaster is not used the feature will remain inoperable because when the set downloads the data, it must find the host channel. It uses the IR blaster to change channels on the CATV box in order to find the host channel. In order for this to operate the customer must use the IR Blaster. If not they will need to split the cable before it gets to the CATV box and deselect any VCR or CATV box questions by answering ""N0"" to questions about them in the initial setup menu. "" | Muller |
Sony | KV35V68 AA-2 | TV Guide Plus | KV35V68 Serial 9005526 TV guide plus does not function. When the television is setup for TV guide Plus the customer is selecting that they have a VCR and CATV box. But they are not using the Calble Mouse or IR Blaster. | The IR blaster is used to communicate from the television to the CATV box in order for downloading to occur. If the IR blaster is not used the feature will remain inoperable because when the set downloads the data, it must find the host channel. It uses the IR blaster to change channels on the CATV box in order to find the host channel. In order for this to operate the customer must use the IR Blaster. If not they will need to split the cable before it gets to the CATV box and deselect any VCR or CATV box questions by answering ""N0"" to questions about them in the initial setup menu. "" | Muller |
Sony | KV36FS10 AA-2 | System control | Unit will turn on but not have any raster until the channel is selected. The LED in front flashes indefinitely until the channel is selected. After a channel is selected the set will run fine the rest of the day. The unit has high voltage, filaments, & vertical sweep during the no raster condition. | After first turning on the set the cathodes of the CRT are measured with an oscilloscope. An interesting fact that after the set is turned on there are no visible IK pulses on any of the CRT cathodes. IK pulses only appear when the channel is addressed with the remote or the Channel up down command on the television. Initialization of the EEPROM did not correct the symptom. No incorrect values found in the alignment parameters. Only by elimination was the trouble found to be in the EEPROM. | Muller |
Sony | KV27V25 AA-2 | system control | Unit has intermittent snow in the picture. 8-598340-20 tuner was replaced. Now the set has a symptom where the remote control causes the set to enter the video input mode when the channel is selected. Also the set will enter the video input mode if another brand of remote that operates a stereo receiver is used. | I instructed the tech to enter the tech mode and set the ID codes...ID0=25, ID1=23, ID2=47, ID3=0, ID4=27,ID5=135, ID6=1, ID7=0 . Write these in memory, then press ""8"" ""Enter"" to initialize. "" | Muller |
Sony | KV27V22 AA-2 | SYSTEM CONTROL | KV27V25 Unit has intermittent snow in the picture zThe tuner pn# 8-598-340-20 was replaced. Now the set has a symptom where the remote control causes the set to enter the video input mode when the channel is selected. Also the set will enter the video input mode if the and another brand of remote that operates a stereo receiver will put the set into the video input mode. | I instructed the tech to enter the tech mode and set the ID codes...ID0=25, ID1=23, ID2=47, ID3=0, ID4=27,ID5=135, ID6=1, ID7=0 . Write these in memory, then press ""8"" ""Enter"" to initialize. This corrected the problem. "" | Muller |
Sony | KV27FV15 AA-2 | SYSTEM CONTROL | KV27F15 The set has a symptom of the keyboard doing the wrong functions. Cannot get into the tech menu. When the display button is pushed the set will shut off. | Checking Key-in to the I001 we found it to be sitting at 3.7 volts without any keys pushed. This is an analogue input to the CPU and must be at 5 volts with no keys pushed. Keyboard had small board contamination on the channel down switch. Removing the channel down switch corrected the problem. All remote control functions return to normal and so did the keyboard functions | Muller |
Sony | KV27S40 AA-2 | squeal | KV35S40Unit is making a noise internal to the television that resembles the sound a fax machine makes when listening to it over a telephone connections | These sounds are apparently caused by loose laminations in the Linearity transformer. It is suggested the tech replace L511=1-406-607-41, C520= 1-101-821-00(.002 mfd @ 500 vdc) R506 =1-215-861-00(47 ohm@ 1 watt Metal film) | Muller |
Sony | KV27V22 AA-2 | SHUTSDOWN | KV27V22 serial 8004933 Unit has a green screen with slight retrace lines, Tapping on the neck of the tube aggravates the green drive then the set shuts off. | CRT.. Due to this trouble I suggest that we replace the CRT A68KZJ50X | Muller |
Sony | KV32XBR48 AA-2 | shuts down | KV32XBR48 Unit get a bright red screen then looses horizontal sweep then shuts down. Unit can be turned on again right away | Tech needs to tap on neck of CRT and see if the symptom is aggravated by this action. After tech got to the house an tapped on CRT it was founf that the Tube was causing the | Muller |
Sony | KV35V35 AA-2 | SHUTDOWN | KV35V35 serial 9011978 Unit flashes bright green with retrace lines then shuts down. When powered back up sometimes the set will be in the ""VIDEO 1"" mode. "" | ?Unit has a defective CRT. A89LJT80X | Muller |
Sony | KV32S65 AA-2 | shutdown | KV32S65 Unit goes into shut down. Will allow HV to com up but goes into immediate shut down afterwards. At no time did we ever have Data on 9 & 10 of the Jungle IC | Open coil that supplied the B+ to the audio controller and buffer chips. This loss in voltage caused the audio processor chip to load down the Data and Clock lines and cause this symptom. | Muller |
Sony | KV32S40 AA-2 | shutdown | KV32S40 Unit will turn on and immediately shut down. It does get high voltage briefly. Appears to be entering over current shutdown. Waveform at the collector of the horizontal output appears normal. Horizontal drive is normal if the horizontal output transistor is removed. | Severing the 135 B+ line and placing a 40 watt bulb in series with the supply were are still getting the same symptom but the Light illuminates brightly. We began to disconnect the flyback loads D530, D531. After disconnecting these we found the set will run with D530 disconnected . Checking this device it passes the static check. This component is the -15 volt source. It was suggested to replace D530. This corrected | Muller |
Sony | KV32S22 AA-2 | shutdown | KV32S22 serial # 8055057. Unit will run fine for 15 ~ 30 minutes with sporadic arcing then it will shut down with a bright green flash | Unit needs replacement CRT 8-733-741-05. | Muller |
Sony | KV24FV10 AA-2 | shutdown | KV24FV10 Unit will shut down immediately after turn on. But the unit will stay on if the service mode is entered.. | When monitoring the VP at IC001(18) only 1 volt peak to peak was measured. Floating IC001(18) allowed the voltage to return to 5 volt PP. Replacing the IC001 corrected the | Muller |