Dicas Reparação SONY
Modelo - Chassis
Pesquisa: SONY Enviar Dica Resolvida
Resultados 18944
Pedir dica reparação
| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | SPP150 | INTERCOM MODE OPERATION | Customer complains the intercom does not work properly.Instructions on page 19 of the instruction manual are not clear. Thehandset will ring once and lock a channel for 1 or 2 seconds. Whatshappening is the customer is going into the talk position afte | ||
| Sony | KV25XBR | NO SOUND OR SOUND CRACKING | No sound or sound cracking on some channels. | ||
| Sony | KV25DXR | NO COLOR ON SCRAMBLED STATIONS ON CABLE | Problem on the Exeter Cable Co. Exeter, New Hampshire(continental). The unit had no color on 1 scrambled station and flashingcolor on the other. Found burst signal - measured 80mv on the stationthat was flashing and 50mv on the one with no color. All | ||
| Sony | PATCH PANL | SONY PATCH PANEL | Does a replacement parts list exist for the test panels usedat our SSCs? In particular,DPDT center off toggle switch3PDT center off toggle switch3PDT 2-position toggle switchSpecial audio SG toggle switchAlso, is a similar bat handled 4PDT (center off, | ||
| Sony | KV27SXR10 | VERTICAL JUMP USING VCR, LEAKY C-1734 | There was a vertical jump in the picture using VCR playback. | ||
| Sony | KV27TX11 | NO BAR DISPLAY, REPLACE IC-101 | No bar display on screen. | ||
| Sony | CDPC20 | INCORRECT OPERATION OF DISC DRAWER | On power-up spindle chassis would drop and carousel wouldspin, but drawer would also open half way and then close. Also, whenchanging from disc to disc, drawer would again open half way and thenclose. Otherwise, unit worked correctly. | ||
| Sony | D4 | INCORRECT VOLTAGES IN SERVICE MANUAL | The voltages around IC-401, Q-407 etc. in the power supplyappear incorrect. If they are incorrect, what should they be? -HQ COMMENTS: Pin 1 = 1.36V, 2 = .92, 3 = 1.74, 4 = 1.2, 5 = 5.72, 6 =0, 7 = 0, 8 = 9.76, 9 = 0, 10 = 3.57, 11 = 2.54, 12 = 1.28, 13 | ||
| Sony | KPR4620 | DUST ON SCREEN, REPLACED SCREEN | Dust on screen. | ||
| Sony | EDC55 | LENS HOOD, LENS CAP AND GRIP BELT PART NUMBERS | The part numbers for the lens hood, lens cap and grip belt areas follows: Description Part Number Lens Hood 3-730-741-01 Lens Cap 3-730-742-01 Grip Belt 3-730-743-01 -HQ COMMENTS: A | ||
| Sony | FD35 | TUNING DIAL FOR FD-35A | Detroit SSC has received four cabinet assemblies (front) andthe tuner dial is missing. There is no part number for dial so I assumethis should be part of the cabinet. Could you please check into this?Thanks. -HQ COMMENTS: Tuning indicator is included | ||
| Sony | CDXA10 | CNP901 LINE OUT CABLE | Cannot identify part number for cable between Jack Board andMain Board. Two versions - older units (serial No. 17627) have a single8-pin connector for the Jack Board and dual 3-pin (5-pin connectors) forthe Main Board. Newer units (serial No. 22395) ha | ||
| Sony | CCDF30 | NO COLOR E-E IN CAMERA MODE | No color from camera section and line in. All other functionsworked properly. Found Q-360 not switching properly. It would not toggleIC-365 on IC-364. Camera 5V out of DC-DC converter was just low enough tokeep Q-362 on about 3.7VDC. This in turn wo | ||
| Sony | CCDV3 | NO CAMERA LUMINANCE | No luminance coming from camera section. Pin 36 of IC-801had no luminance signal, all DC voltages were correct and all signals toIC-801 were present - YH, B-Y, R-4 and YL-YH. Changed IC-801 still noluminance. | ||
| Sony | KV27SXR10 | LINE ACROSS TOP OF SCREEN, AG HOLDER, NO SOLUTION | The outside tech in Costa Mesa informed me of customerscomplaining about the three band that hold the aperture grille fromoscillating. The problem is the customer can see the top line from adistance of 7 to 8 feet. The tech has been out to four custome |