Dicas Reparação SONY




Modelo - Chassis


Pesquisa: SONY Enviar Dica Resolvida
Resultados 18945
Pedir dica reparação
MarcaModelo
(Chassis)
SintomaCausaSoluçãoPor:
SonyCDP101
RF PLL AND CLV PLL OUT OF ADJUSTMENT The unit does not accept the customer's disc. Decca, Verdi,La Travia (400057-2). It worked fine with YEDS-1.
SonyCDP101
MALFUNCTIONING D/A CONVERTER IC507 The unit had an intermittent low pitched buzz in bothchannels. We found IC507 D/A converter to have an intermittent clock.
SonyWMF10
INTERMITTENT AUDIO Ground becomes discontinuous due to excessive lubricant onhead ground plate surfaces. Remove lubricant. Use Sony P-401G to Relube. -HQ COMMENTS: We will issue a bulletin on WM-10 lubrication pointsshortly.
SonyTCFX7
EXCESSIVE WOW AND FLUTTER PLUS MOTOR NOISE Motor comes with plastic clutch, which in time will comeflush against motor bearing, causing a grinding noise and wow and flutter.One solution is to put a small plastic washer at clutch shaft assy tostop it from going inwards against motor bearing. -HQ
SonySRF5
INTERMITTENT AUDIO - HOW TO SERVICE When the plastic interconnecting strip is removed, you cannothear audio (because the audio-tuner parts are separated). What is therecommended troubleshooting procedure? -HQ COMMENTS: 1) Complete B+ and ground connections for the tuner asoutlined on Pag
SonySPP11
NO VOICE SIGNAL THROUGH THE HANDSET SPEAKER The hand unit and the base unit communicate with each otheras indicated by an operational key pad and dial tone, but there was novoice through the speaker. Found C53 (0.047uF) was shorted inside.Replaced it.
SonyPSX55
PART NUMBER - DET SW CONTACT SLIDER A servicer tried to order the contact slider. Since the partnumber is not listed in the service manual, he thought it is included inthe cam control (#4-869-957-00) and he ordered it. But the contact sliderdid not come with it.
SonyPSLX55
ERRATIC MOVEMENT OF TONE ARM The tonearm on this unit would cue into the record at afaster pace than it would cue in the outward direction. Glue on the PCboard has erroded and was responsible for changing the DC level on Pin 1of IC202. A resultant -2.5 VDC was present at IC202's o
SonyXR50
CASSETTE EJECTED SOON AFTER LOADED Cassette ejected soon after loading. The DM-101A(P/N 8-745-101-01) DME had failed along with Q602 (voltage reg) and D602(voltage ref). -HQ COMMENTS: The output of my sample DME is a sine wave of 0.1VACcontaining a 3.6VDC component. Its output is a pro
SonyTC48
PART NUMBER FOR GEAR (C) I need P/N for gear (C) on Page 14 of service manual. -HQ COMMENTS: Gear C shown in the exploded view is part of the flywheelassembly. It is press fitted onto its shaft, and cemented. Recently,however, this gear has been made available as P/N 3-550-02
SonySTRVX550
MUSIC STOPS AND NOISE OCCURS Unit would play on FM and intermittently go to noise. Displaywould remain unchanged and tune light stayed lit. I found taping on powersupply caused problem to come and go. Found the ground connection to bethe problem on that main board. Put in a star
SonyPSX800
INCORRECT PART NUMBER - D606 Incorrect P/N listed for 20V zener D606 on Page 54 ofmanual. P/N listed 8-719-990-03 should be 8-719-910-03.
SonyPSLX5
INCORRECT SET - DOWN POINT When a 12 record is placed on turntable, tonearm goes to7 position. Replaced Q209 with new type transistor 2SA1027R, as perS/B #155. This transistor insures pull in of the size solenoid.
SonyPSLX1
PART NUMBER - CARTRIDGE WIRES The technician could not find the parts numbers of thecartridge wires. -HQ COMMENTS: Although the parts numbers are listed in the S/M(#512 1-555-828-00 White #513 1-555-829-00 Red), they are notindicated in the exploded diagram on P17.
SonyCF420
MECHANISM SHUTS OFF The mechanism shuts off in any mode before tape ends. Forsome reason, the shut-off safety plate did not engage the brake lever.Put it back on the brake lever.


Assistência TécnicaAs dicas apresentadas destinam-se a técnicos de eletrónica, a tentativa de reparação ou assistência sem ter conhecimentos de eletricidade e eletrónica, podem provocar danos mais graves aos equipamentos e, devido a tensões muito elevadas em alguns circuitos, graves danos fisicos que podem constituir um risco em determinadas reparações.

Não arrisque reparar equipamentos com tensões elevadas se não tiver conhecimentos técnicos para o fazer em segurança.

Verifique se o esquema está disponível na área de downloads