Dicas Reparação SONY




Modelo - Chassis


Pesquisa: SONY Enviar Dica Resolvida
Resultados 18945
Pedir dica reparação
MarcaModelo
(Chassis)
SintomaCausaSoluçãoPor:
SonyKP5000
CONVERGENCE CHANGE, REPLACED GREEN CRT When setting unit up for convergence by placing hatch patternon screen, the set would set up nicely. Then when switching the crosshatch off, the pix looked severely mis-converged. Closer inspectionrevealed that only the green was mis-converged and in v
SonyTV520
NO PICTURE No video when replacement CRT is used. Have had 5 reports ofthis problem. P/N 8-731-105-15, CT-450 is being subbed by 1-546-039-00.This replacement has an adapter socket to use. However, when hooked upno video is received. -HQ COMMENTS: Installing th
SonyTV115
INTERMITTENT AGC This unit displayed very intermittent AGC. Under very strongsignal conditions it would play well. We found R333 to be thermallysensitive. It looked fine however, no signs of overheating.
SonyKX2501
DEAD, REPLACED D1206 Dead. EVP-1 ckt OK, shutting down PPS. Replaced open R675,produced raster. Hooked up a VTX-1000R unit smoked and went dead. R675open again, Q1343 open, R02 burned. Replaced all parts.
SonyKX2501
NO POWER, REPLACED T652 This unit had no drive to the converter output on GA board.We found the primary of T652 to be open.
SonyKV9000U
INCORRECT PARTS COMPATIBILITY Servicer ordered thyristor from distributor using P/N1-801-010. This number subs over on the microfiche to P/N 8-719-000-10.In the semiconductor replacement handbook, page 321, diagram #D040 showsthe lead configuration of the substitute part. If this c
SonyKV2648R
A SMALL PURITY SPOT ON THE SCREEN, REPLACED C801 This unit had a small purity spot on the right-hand side ofthe screen. After much adjustment we nearly concluded that the CRT wasdefective. Further examination revealed the ETC ckt to be the cause.Disconnecting the ETC coils eliminated the problem. We
SonyKV2648R
INCORRECT COLOR, RESOLDERED IC4005 PIN 14 Bad color. Hue was bad. Could be mistaken for purityproblem. Found bad solder connection at Pin 14 of IC4005.
SonyKV2647R
PART OF PICTURE BLANKING OUT, R557 VALUE CHANGED Horizontal problem. Part of pix blanked out. Frequency notstable. Found R557/1.2 ohm resistor had climbed in value to 12 ohms.Resistor located on the 15V line.
SonyKV2647R
INTERMITTENT NO CHANNEL RECEPTION, REPLACE R-025 This unit would not tune stations intermittently. Found R025/22K ohm resistor increased in value to 35kohm on MF board.
SonyKV2647R
NO CHANNEL 11 RECEPTION, REPLACE IC002 This unit would not tune channel 11 in all the way. Thescreen displayed a HERRING BONE pattern. At first it appeared to be anAFT problem. However further investigation revealed IC002 memory to bedefective.
SonyKV2645R
POPPING SOUND ON CHANNEL CHANGE, REPLACED T207 Servicer had replaced T207, hoping to cure a highly inter-mittent sound loss problem. Set was returned to shop and I noticed apopping sound on channel change.
SonyKV2601
INTERMITTENT ALL CHANNEL DISPLAY Intermittently unit would go to all channel display lightslit. Could not tune in any station when all lights locked in. Foundnegative line off flyback OK but after going through coil L511 found thatthe negative voltage sometimes missing. Also serial n
SonyKV2602
INTERMITTENT SHUT DOWN, REPLACED IC501, D501, Q501, T502 Intermittently goes into HV shut down. Changed IC501, D501,Q501, T502. Also reduced the value of R572 to satisfy the adj. procedure. -HQ COMMENTS: Probably this type of shut down is caused by defective HVRblock. The 15.2 +/- 0.1V specified in adjustm
SonyKV1946R
PICTURE DISTORTION (V), REPLACE IC502 Would not scan top 2 inches of picture V-size and lin. hadno effect, remove blanking and fills up picture.


Assistência TécnicaAs dicas apresentadas destinam-se a técnicos de eletrónica, a tentativa de reparação ou assistência sem ter conhecimentos de eletricidade e eletrónica, podem provocar danos mais graves aos equipamentos e, devido a tensões muito elevadas em alguns circuitos, graves danos fisicos que podem constituir um risco em determinadas reparações.

Não arrisque reparar equipamentos com tensões elevadas se não tiver conhecimentos técnicos para o fazer em segurança.

Verifique se o esquema está disponível na área de downloads