Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CFD616 | INTERMITTENT CD JAMMING OR NOISE | Cust had complained of rubbing noises and occasional jammingof CDs in unit. After much dissassembly and checking, servicer found thatref#225 lever(T) was not meshing properly with ref#262 gear(L1). This wasdue to post on Chassis(sub) assy ref#263, being | ||
Sony | CFD616 | NO REF # FOR CD PLASTIC CHASSIS | Need part # for plastic chassis on pg 39 of sm. It is theplastic chassis that fits on top of chassis sub assemble #263. It doesn'tseem to be listed in the manual or supplement #1 issued for unit. -HQ COMMENTS: Contact Kansas City Parts, attn Jamie Ly | ||
Sony | CFD600 | CD JAMMED | CD's jammed in unit. Suspect unit is transported with a CDin the play/spindle location, then gets bounced around affecting theloading alignment. Cust then turns on unit and drive loads incorrectly.I have instructed cust not to transport unit with cd's | ||
Sony | CFD600 | DISK BASE MISSING STOPPER | Stopper is missing in new disk base. See attached copy.This can accidently cause the disk base to lock up. | ||
Sony | CFD600 | DISC DRAWER DOESN'T CLOSE SMOOTHLY | After replacement of disc base, drawer, found new part hitssomething as it closes which causes drawer to move upward and overobstruction. Since old drawer did not have this problem there must bea difference between old and new one. | ||
Sony | CFD600 | MECHANISM JAMS | CD mechanism jams. Several reports have been submittedregarding this problem. | ||
Sony | CFD600 | CD CHANGER MECH JAMMED | Received unit with CD jammed in changer. Removed CD's.Physically turned gear Ref 267 so elevator gear brought the case (ref269) all the way in the up position. Powered unit, the eliminator mechwent down and jammed. | ||
Sony | CFD600 | WHEN PLAY IS PRESSED, UNIT INDICATES TAKE OUT DISC | When all the discs are loaded and play is pressed, unitindicates: Take out disc on every disc you attempt to play, 4th unit withthis problem. | ||
Sony | CFD600 | CHUCKING PROBLEM | Disk chucks out of alignment sometimes. This causes thedisk to rub on mechanical assembly. | ||
Sony | CFD600 | CAN'T MOUNT SLED MOTOR ON NEW TURNTABLE ASSY | New spindle motor comes attached to the turntable assy. Whenattaching old parts to new turntable assy the holes for the sled motordon't line up. With some dificulty the new spindle motor can be removedand put on old turntable assy. -HQ COMMENTS: Conta | ||
Sony | CFD600 | WRONG SPINDLE MOTOR | Spindle motor does not line up on cd motor board ref 251.Spindle motor was ordered twice with same results. -HQ COMMENTS: Contact Kansas City Parts, attn Jamie Lyon phone #816-891-7550 ext 256, fax # 816-891-2580. | ||
Sony | CFD600 | REPLACEMENT TURNTABLE ASSEMBLY DOES NOT LINE UP | The replacment turntable assemblies do not permit the cdmotor board to line up correctly with the spindle motor, and the sledmotor does not line up with the drilled holes. Please advise. -HQ COMMENTS: Contact Kansas City Parts, attn Jamie Lyon phone # | ||
Sony | SVT5000 | VERY POOR PICTURE QUALITY | Found RF level very low, causing poor picture quality especially on exit side. 3rd unit with problem in 1 month. | ||
Sony | SLVR5UC | TAPE INDICATOR WRONG/ HIGH SPEED REWIND WON'T STOP SMOOTHLY | 1. The unit may display the wrong tape indicator (tape may be full, while the incator may show mid range...) 2. High speed rewind won't slow down as the tape approaches the end and it will not stop smoothly. | ||
Sony | SLV940HF | WON'T ACCEPT TAPE - RELACED FL ASSY LOADING GEAR SLIDE ASSY | Won't accept tape. |