| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CDPC445 | TRAY WON'T STOP ON RIGHT DISK - REPLACED TABLE MOTOR | Tray won't stop on right disk or may heitate to run. | ||
| Sony | CDPC345 | WHISTLING NOISE - ADD RTV BTWN SPINDLE MOTOR & BD BOARD | a whistling noise (about 400HZ) manifists itself on certain cuts of disc (Goodbye Yellow Brick Road, Elton John, Polydor D103076). If you touch the optical block lightly, the noise disappears. | ||
| Sony | CDPC265 | JAMMED DRAWER - REPLACED MISSING SCREW AND BROKEN LOCK LEVER | Unit came in with drawer jammed found bu assembly loose inunit and lock lever broken. Found screw that holds the bu down was neverput in the unit. | ||
| Sony | CDPC265 | NO PLAY - STAPLE STUCK TO CHUCKING MAGNET | Unit would not play due to staple being stuck to chuckingmagnet. This was an out of box failure. | ||
| Sony | CDPC265 | WILL NOT LOAD - REALIGNED U/D GEAR | Unit would not load disc due to u/d gear beingjammed/misaligned. | ||
| Sony | CDPC265 | SKIPS ON OUTER TRACKS - REPLACED OPTICAL BLOCK | Unit would skip particularly on outer tracks. Not possibleto adjust focus bias correctly. | ||
| Sony | CDP361 | DIFFERENT OPTICAL BLOCK | Optical block specified in manual is KSS240. Optical blockin the unit is KSS213/884836711. Do we have any information regardingthis change? Is there any change to the BD board? -HQ COMMENTS: Update 12/12/95: Service Manual Supplement-1 (p/n9-960-0 | ||
| Sony | BM577 | TAPE STOPS AFTER FEW SECOND ON DICT/PLAY, MISSING REFLECTOR | On either dictate or listen, after a few seconds tape stopsand tape end alarm sounds. | ||
| Sony | XRC620 | ROTARY MODE SWITCH S901 FAILS, CAUSES DAMAGE TO REEL BRACKET | Mode switch fails prematurely causing reel bracket assy to bedestroyed. When reel bracket is replaced also replace rotary mode switchas well (p/n 1-692-885-11). This will prevent intermittent rotaryswitches from eating the reel bracket assy.This FPR was | ||
| Sony | XRC410 | ROTARY MODE SWITCH S901 FAILS, CAUSES DAMAGE TO REEL BRACKET | Mode switch fails prematurely causing reel bracket assy to bedestroyed. When reel bracket is replaced also replace rotary mode switchas well (p/n 1-692-885-11). This will prevent intermittent rotaryswitches from eating the reel bracket assy.This FPR was | ||
| Sony | XRC210 | ROTARY MODE SWITCH S901 FAILS, CAUSES DAMAGE TO REEL BRACKET | Mode switch fails prematurely causing reel bracket assy to bedestroyed. When reel bracket is replaced also replace rotary mode switchas well (p/n 1-692-885-11). This will prevent intermittent rotaryswitches from eating the reel bracket assy.This FPR was | ||
| Sony | XRC190 | ROTARY MODE SWITCH S901 FAILS, CAUSES DAMAGE TO REEL BRACKET | Mode switch fails prematurely causing reel bracket assy to bedestroyed. When reel bracket is replaced also replace rotary mode switchas well (p/n 1-692-885-11). This will prevent intermittent rotaryswitches from eating the reel bracket assy.This FPR was | ||
| Sony | XR6450 | ROTARY MODE SWITCH S901 FAILS, CAUSES DAMAGE TO REEL BRACKET | Mode switch fails prematurely causing reel bracket assy to bedestroyed. When reel bracket is replaced also replace rotary mode switchas well (p/n 1-692-885-11). This will prevent intermittent rotaryswitches from eating the reel bracket assy.This FPR was | ||
| Sony | XR6450 | SLOW TAPE SPEED (FOUND MAIN MOTOR M901 DEFECTIVE) | Cassette runs slow. Tried adjusting pontentiometer in motorto no avail. | ||
| Sony | MDXC150 | SPINDLE MOTOR DOES NOT RUN (RESOLDERED IC201) | CLV would not spin. No voltage or signal from IC302 pin 2 &44. IC302 was getting its error signal (pin 41) from IC301 pin 39.This was a tough problem because this is the signal for both directionand initial kick spin of the CLV. |