| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CDPC26 | WILL NOT READ DISC | Does not play disc. | ||
| Sony | SLV272UC | PART NUMBER NOT ON COMPUTER | Gear in mechanism is cracked. Part number is not stocked. -HQ COMMENTS: The part number was entered in the KC system on 3/1/91, soan order must be placed to get stock. Please place an order for the part.There is stock in Japan. | ||
| Sony | CCDSP5 | WRONG PART NUMBER | The part number for reference 156 is incorrect. | ||
| Sony | WMF2031 | WRONG PART NUMBER FOR IC-301 | The P/N listed in the S/M for IC-301 (8-759-820-21) isincorrect. | ||
| Sony | TAAX301 | WRONG PART NUMBER - FRONT PANEL ASSEMBLY | The correct part number is X-4911-213-1. -HQ COMMENTS: A service bulletin will be written to forward thisinformation to the field. Thanks for the information. | ||
| Sony | FHB5CD | WRONG PART NUMBER POWER CORD (US) | The correct part number is 1-575-706-11. -HQ COMMENTS: Thanks for the information. A service bulletin will bewritten to notify the field. | ||
| Sony | CCDV5000 | NO AUDIO FOR 1 1/2 SECONDS AFTER PAUSE | When customer takes unit out of pause mode, he has no audiofor 1 1/2 seconds. This causes a problem when editing. -HQ COMMENTS: This is normal operation. The audio must be muted untilthe servos come up to speed, otherwise there would be noise from the | ||
| Sony | KV32XBR65 | SRS DISTORTION, SEE SB 45R1 | SRS distortion.Solution: Replaced SRS Moduel -HQ COMMENTS: Please replace the moduel with the new one as perservice Bulletin 045.SRS Moduel 8-741-592-02Moduel Bracket 4-393-435-05 | ||
| Sony | ITK500 | COMPATIBILITY PROBLEM WITH PCB, TEL-KEY(NEW VERSION) | The new version of the PC BOARD, TELEPHONE KEY part number1-618-217-11 has only 8 wires out of its connector. The old board and theservice manual shows 10 wires out of the connector. Is there anycompatibility problem between the two boards? -HQ COMMEN | ||
| Sony | SLV373UC | PART NUMBER FOR TK-7 BOARD | The part number in the Service Manual for the TK-7 board(1-634-742-11) indicates Part Not Found both in KC and RPC. Is this agood number? Can you please advise? -HQ COMMENTS: This board is not available as a replacement part. | ||
| Sony | CDPC705 | TORN PRINT ON PCB | When you remove IC-102 with Pyro pen, too much glue has beenput underneath IC. When you try to remove the IC, the print tears up thecircuit board. -HQ COMMENTS: The glue used is necessary during the manufacturingprocess to secure the components to the | ||
| Sony | CDPC85ES | TORN PRINT ON PCB | When you remove IC-102 with Pyro pen, too much glue has beenput underneath IC. When you try to remove the IC, the print tears up thecircuit board. -HQ COMMENTS: The glue used is necessary during the manufacturingprocess to secure the components to the | ||
| Sony | CCDF30 | NO EJECT | Intermittent - won't eject or play. | ||
| Sony | KV32XBR50 | EXCESSIVE HORIZONTAL SIZE (HOR. OVERSCAN),L501 | Q-505 (pin-out) and Q-503 (H-out) were both shorted. Whenreplacing these defective components, there was excessive horizontal widthon screen. H-size could not be adjusted to normal size. Found L-501shorted. Good coil reads 4.9 Ohms. Defective coil r | ||
| Sony | CDPC75ES | TORN PRINT ON PCB | When you remove IC-102 with Pyro pen, too much glue has beenput underneath IC. When you try to remove the IC, the print tears up thecircuit board. -HQ COMMENTS: The glue used is necessary during the manufacturingprocess to secure the components to the |