| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | XR7150 | LINE OUTPUT LEVEL SPECIFICATIONS | One of our non-servicing dealer/installers inquired about theline output levels for our car steroes. He feels it is lower than thestandard 500-mV, but no spec is given in owners manual or service manual.Also no information for input levels for our equal | ||
| Sony | KVX370 | NO POWER | No power | ||
| Sony | CCDV5 | NO VIDEO FROM CAMERA SECTION. | There was no output from the camera section. The 20 voltsto pins 10-9 or the CCD imager IC-701 were missing. Capacitor C-703was shorted. | ||
| Sony | EDV7500 | NO OPERATION | This unit did not turn on. There was no ever five volts totimer board (FF-26). The diode D403 of the servo board (ST-23) wasopened. | ||
| Sony | SRS55 | WRONG PART NUMBER FOR IC1 | The IC1 part number should be 875984125, instead of 875980173. -HQ COMMENTS: The original units (S/N 90400 and earlier) used a LA-4125The P/N for this IC is 875984125 and is listed correctly in the S/M.Later production (S/N 90401 and later) uses a LA-45 | ||
| Sony | TCWR510 | PAUSE LIGHT OPERATION | When should the pause indicator operate? Does it operateonly with the remote or should it operate anytime? -HP COMMENTS: The pause indicator will only be on when the pausefunction is activated using the remote. The pause button on the frontpanel will | ||
| Sony | KV2728R | PICTURE UNSTABLE HORIZONTALLY, REPLACE C-1537 ON D BOARD | Problem looked like poor horizontal AFC lock. Slight fold-over on left side and picture would shift from right side to left side.It looked like unstable horizontal sync. | ||
| Sony | SLV70HF | LOADS, UNLOADS THEN SHUTS DOWN. EJECT ONLY WORKS. | When play is pressed unit loads, unloads and shuts down.It will only eject after this. Also the VTR switch will switch offthereby returning to TV operation. | ||
| Sony | WMF701C | BROKEN POST FOR REEL SPINDLE | The post for the Reel Spindles (Ref. # 318 and 321) breakoff from the chassis (Ref. # 353). The post is attached to the chassisby slightly flaring the bottom of the post. In the cases I haveseen, the post simply pulled through the hole. -HQ COMMENTS: | ||
| Sony | KV27XBR10 | 4 INCH BLANKING BAR ON RIGHT SIDE, REPLACED IC-301 | Unit comes in with the Blanking Bar about four incheson right side of screen. | ||
| Sony | SLHF860D | WILL NOT PLAYBACK OR RECORD | Unit will accept tapes, load, threads and you can rewind orFFW. If you hit (Play) or Record, there is no movement and no buttonswill work even Power ON/OFF. You have to unplug the unit to eject thetapes again. | ||
| Sony | DT3 | LASER STAYS ON CONTINUOUSLY | IC-501 (CXA-1081Q) has LD on (pin 10) permanently tied low.This pin normally controls the laser on output from the IC. If pin 10 islow, the laser is on. Does this mean the laser is always on in this unit? -HQ COMMENTS: Not exactly. The power supply t | ||
| Sony | D3 | LASER STAYS ON CONTINUOUSLY | IC-501 (CXA-1081Q) has LD on (pin 10) permanently tied low.This pin normally controls the laser on output from the IC. If pin 10 islow, the laser is on. Does this mean the laser is always on in this unit? -HQ COMMENTS: Not exactly. The power supply t | ||
| Sony | CFS4000 | REPLACEMENT COUNTER BELT DOES NOT FIT | Replacement counter belt is too large by about 1cm. The beltis replaced by part number 3-642-544-XX. Please advise us as to anotherpart number. -HQ COMMENTS: The counter belt, ref. 359, part number 3-434-110-XX isreplaced by part number 3-657-035-XX. | ||
| Sony | KV27XBR10 | DISTORTED AUDIO IN SRS MODE, REPLACED SRS MODULE, SB 45R1 | Audio was distorted in one channel when in the SRS Mode. |