| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CFS903 | KEYPAD (RUBBER COVER) BREAKS (TEARS) EASILY AND PREMATURELY | Sample forwarded for evaluation and pad replaced. A monthlater it had to be replaced again due to breakage. The customer claims noabuse. -HQ COMMENTS: Please reorder the MD Button Packing using the partnumber for the new improved part. The material c | ||
| Sony | D2 | REPLACEMENT ASSEMBLY IDLE GEAR BINDS | Replacement assembly idle gear binds. Getting several re-calls in service center. I am enclosing sample unit. This unit binds andskips intermittently. Motor assembly has been replaced in unit. -HQ COMMENTS: Due to design limitations, cost and part s | ||
| Sony | KV2681R | IC-301 CHIP SUBSTITUTION, CX-20129 TO CX-20193 | The original IC-301: CX20129, part number 8-752-012-90 wastemporarily not available. Tried using CX20193 but picture was rollingvertically. Can this chip be used as a substitute? References: Seeservice bulletin CTV0236 and 24. -HQ COMMENTS: When usin | ||
| Sony | CCDSP7 | NO VTR FUNCTIONS | Found no VTR functions after loading of tape. Unit doeseject and works fine in camera mode. Unit acts like it is in OFFposition. | ||
| Sony | FD500 | DEAD - IC-451 LOADED (SOUND OUTPUT IC) | Unit arrived dead. Found fuse (F-602) blown. Checked andfound IC-451 with a chipped-off body. Found this problem very common forFD-500. This unit had previous problem of a blown IC-451. Prematurefailure of IC-451 and F-602 is too high. | ||
| Sony | DT2 | PRODUCTION CHANGE IN SPINDLE MOTOR ASSEMBLY | I have noticed that newer models have new motor assemblies(X-264-153-72) installed from manufacturer. They also have a new MD cover(Ref. No. 73) with a different finish. Do models with new MD covers allhave new motor assemblies? Or do you have a list | ||
| Sony | DT4 | PRODUCTION CHANGE IN SPINDLE MOTOR ASSEMBLY | I have noticed that newer models have new motor assemblies(X-264-153-72) installed from manufacturer. They also have a new MD cover(Ref. No. 73) with a different finish. Do models with new MD covers allhave new motor assemblies? Or do you have a list | ||
| Sony | D4 | PRODUCTION CHANGE IN SLED MOTOR ASSEMBLY | I have noticed that newer models have new motor assemblies(X-264-153-72) installed from manufacturer. They also have a new MDcover (Ref. No. 73) with a different finish. Do models with new MD coversall have new motor assemblies? Or do you have a list | ||
| Sony | D2 | PRODUCTION CHANGE IN SPINDLE MOTOR ASSEMBLY | I have noticed that newer models have new motor assemblies(X-264-153-72) installed from manufacturer. They also have a new MD cover(Ref. No. 73) with a different finish. Do models with new MD covers allhave new motor assemblies? Or do you have a list | ||
| Sony | CCDF45 | NO PART NUMBER FOR FRAME | I need the part number for the frame to which the lens andmechanism are attached. It is shown on page 175 next to item No. 115.It is labeled not supplied. When I received a unit for repair, whichwas dropped, this part is usually damaged. There are man | ||
| Sony | CDPC100 | DISC SPINS BACKWARDS | Disc would spin backwards. Reversed motor leads and unitwould play ok until IC-202 warmed up then spindle motor would again runbackwards. | ||
| Sony | D9 | NO DISC ROTATION | Spindle motor would not operate. | ||
| Sony | PCM601ESD | INTERMITTENT AUDIO OUTPUT DURING PLAYBACK | Intermittent audio output during playback. Video out is notaffected. Traced signal to IC505-9. Signal is always the same regardlessof whether or not audio is present. However, output at IC505-7 woulddisappear when audio is missing. Also noticed that | ||
| Sony | STRAV910 | UNIT DEAD - NO POWER OR DISPLAY | Unit is dead. No power and no display. | ||
| Sony | SPP60 | PART NUMBER MISSING - IC-6 IN THE BASE UNIT | There is no part number listed in the S/M for IC-6 (BR93C46).The part number is also not listed in the newest Semiconductor ReplacementGuide. We need the part number. -HQ COMMENTS: Part number for IC-6 is 8-759-995-59. |