Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | CFS4000 | MISSING PART NUMBERS - PACKING MATERIAL | Need part # -HQ COMMENTS: The part numbers are as follows:3-333-977-01 Protection Sheet3-333-979-01 Cushion3-333-984-01 Spacer3-333-997-01 Prevention Sheet3-333-980-01 CartonWe will issue a S/B. | ||
Sony | KV25XBR | STEREO LIGHT BLINKING | Stereo light indicator blinks even when receiving nonstereochannels. | ||
Sony | TAAX520 | ONE CHANNEL OUT | This is the second unit we have seen with the same problem.The solder connections on the input board from the input jacks arebreaking loose. The first unit had one channel out on phono. This unithad one channel out when the equalizer was used. Both we | ||
Sony | SLHF900 | INTERMITTENT PAUSE RELEASE | Once every 10 or 20 times during pause release the tape gotdamaged by the machine. The cause was that the take-up reel did not turnas a result tape wrapped around capstan shaft. | ||
Sony | KV2781R | DEAD, RESOLDER H DRIVE TRANSFORMER | Set came in dead, scoped horiz osc and I had an output, scopedhoriz driver Q551 collector and had an output. Scoped base of horizoutput, found no signal. Traced problem to driver (secondary) trans-former. | ||
Sony | KV2782R | SLEEP LIGHT COMES ON, NO OTHER FUNCTIONS, REPLACE R-555 | With unit turned on, sleep light would come on, hi-voltagewould come up, no other functions, no sound, no raster. Scoped IC101 onA board, Pin 7 found no vertical pulse. Traced problem to D board,found no vertical output. Found no 27 volts on Pin 7 of | ||
Sony | KV25XBR | SLEEP LIGHT ON, HIGH VOLTAGE ON, NOTHING ELSE | Unit turned on, sleep light comes on, Hi voltage comes on,no raster, no sound, no functions. Found vertical pulse missing onPin 4, IC103 on A board. Traced problem to Q127, base had vertical,nothing on collector. Transistor was opened. | ||
Sony | XR27R | INCORRECT PART NO. | Servicer ordered above part No. (1-237-124-11) that is listedin service manual. Part was wrong size for XR-27R. | ||
Sony | KV2649RX | FUNCTIONS INOPERATIVE, REPLACED X001 | Set would turn on and off manually but no other functionswould work. Only problem we could find was clock signal at Pin 1 IC001was correct freq. but was about 2.3Vpp. | ||
Sony | KV2783R | SLEEP LIGHT ON, SET WAS DEAD, REPLACE IC-501, R-555 N DIODES | Sleep light on, set was dead. Both damper diodes shorted,R555 on 24V line was open. Troubleshooting revealed no switching pulseat base of Q553 which probably accounted for defective damper diodes.Further check revealed IC501 to be defective, causing R5 | ||
Sony | KV2681R | NO SOUND, REPLACE T-1104 ON X BOARD | Set had no sound. After considerable time spent in tryingto isolate defective part, I determined T1104 had to be open. Bridgingit with a 0.05 capacitor restored sound. By the way, it was very diffi-cult to trace audio to determine where the problem wa | ||
Sony | EVC8U | NO PART NUMBER FOR FLEX CONNECTORS | Can not find P/N for flex connectors shown in explodeddiagram on page 101. -HQ COMMENTS: Connector part numbers are listed on pages 108 and 114 ofS/M. Part numbers are 1-557-555-11 (CN509, SV-13) and 1-562-583-11(CN506, MC-4). | ||
Sony | CCDV8AFU | NO Y INFORMATION | Picture camera looks like chroma with no video. Bluish redimages slightly smeared. | ||
Sony | CCDV8AFU | NO RECORDING | Unit playback was fine. Would not record anything at all.Snow was all that was on tape. All necessary signals were present,video, sync, record correct. Would erase previous information. | ||
Sony | CDP650ESD | ALIGNMENT | After installing BU-1C, alignment difficult to perform forRF PLL. |