Service Mode (Modo de Serviço)

PHILIPS

ANUBIS A chassis 8 local controls

CTV

Hotel Mode

First Method Activation Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set. De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When de- activation is OK, a "H-" is displayed. To remove this display turn off-on the TV set.'

PHILIPS

ANUBIS A chassis 2 local controls

CTV

Hotel Mode

Third Method Activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When activated "HOTEL MODE" a green "H" is displayed. To remove this display turn off-on the TV set. De-activation Select program 38, then press "INSTALL" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec. When de-activation is OK, a green "H" is displayed. To remove this display , turn off-on the TV set.

PHILIPS

ANUBIS A chassis 2 local controls

CTV

Hotel Mode

First Method Activation Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set. De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" (or "OSD") on remote control for at least 4 sec.. When de- activation is OK, a "H-" is displayed. To remove this display turn off-on the TV set.'

PHILIPS

TV/VCR chassis

CTV

Hotel Mode

Activation Select program 38, press "SELECT" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec.. At activation the "H+" is displayed. To remove this display turn off-on the TV set. De-Activation Select program 38, then press "SELECT" on local keyboard and "SLEEPTIMER" on remote control for at least 4 sec.. When de-activation is OK, a "H-" is displayed. To remove this display turn off-on the TV set.

NOKIA

CTV

Service Mode

First Method - set with CCU12 uPC: press the contact behind the small borehall on set front pannel (controls) and then button "S" whithin 5 sec. Tha display shows "SE".

NOKIA

CTV

Service Mode

First Method - set with CCU11 uPC: press buttons from remote controls "mon-stereo" - "C" - "hypersonic" whithin 1 sec. Tha display shows "SE".

PANASONIC

SOM

Service and Test

- Assegure-se que não há nenhuma cassete em nenhum tape. Pressione TAPE. Pressione TUNING, por 2 segundos. Sem soltar Tuning, pressione MEMORY/SET, por 2segundos. Deverá aparecer no display: "T". Indicando que está em modo de serviço. NTRAR EM MODO DE TESTE Do CD - Estando em Modo de Serviço pressione: 1 - a tecla CD 2 - Pressione TUNING MODE por mais 2 segundos. 3 - Sem soltar a tecla Tuning Mode pressione MEMORY/SET - Automáticamente aparecerá no Display a mensagem diagnostico de falhas.

PANASONIC

TV

Service Mode

Method 3 Tx-W28r3 (And Similar Models) 1. Set Bass To Maximum Position, Set Treble To Minimum Position 2. Press Reveal On The Remote Control And At The Same Time Press Volume On The Tv. This Will Place The Tv Into The Service Mode 3. Press The Red / Green Buttons To Select An Item 4. Press The Yellow / Blue Buttons To Adjust 5. Press Store On The Preset Panel After Each Adjustment Has Been Made To Store The Required Values 6. To Exit The Service Mode, Press Normalization

PANASONIC

TV

Service Mode

Method 2 1. Short Test Point Fa1 To Cold Ground Fa2 (A-Board: Tp Pin 8 To Pin 3) 2. Receiver Is In Aging Mode With Yellow 'Chk' In The Upper-Left Corner 3. Press Action And Vol+ Simultaneously On The Control Panel And 'Chk' Should Be In Red 4. The Set Is Now In Serviceman Mode, Press Power On Remote To Select One Of The Five Serviceman Adjustment Modes: B = Vcj Sub Adjustments C = Crt Adjustments D = Pincushion Adjustments S = Options Adjustments (Pip And Clock) 5. Press Chan Up / Down On Remote To Select An Item 6. Press Vol Left / Right To Adjust 7. Press And Hold Power And Action For A Few Seconds To Save And Exit Service Mode. Set Will Turn Off And Then Back On By Itself

PANASONIC

TV

Service Mode

Method 1 For Chassis Amedp, Apedp, Aredp ... 1. Press Action (Tv Turned On) 2. Select Set-Up Icon, Set Antenna To Cable 3. Select Timer Icon, Set Sleep Timer To 30 4. Press Action Twice To Exit Menus And Tune To Channel 124 5. Adjust Volume To 0 6. Press Vol - On Tv Control Panel And Red 'Chk' Will Appear In The Upper Left Corner 7. To Toggle Between Serviceman And Aging Modes Press Action And Vol + Simultaneously On The Control Panel 8. The Set Is Now In Serviceman Mode, Press Power On Remote To Select One Of The Five Serviceman Adjustment Modes: B = Vcj Sub Adjustments C = Vcj Cut-Off Adjustments S = Options (Pip And Clock Adjustments) M = Mts Adjustments 'Chk' = Normal Operation Of Channel And Volume Controls 9. Press Chan Up / Down On Remote To Select An Item 10. Press Vol Left / Right To Adjust