Service Mode (Modo de Serviço)
Marca
Mod.
Ch.
Tipo
Modo
Proced.
File
BEKO
TV
Service Mode
Service Mode adjustments
1-White balance Adjustment- Switch on TV over mains while pressing up/down buttons on control unit.
2-Push balance on remote.
3-push colour button
Beko AT3 Service Mode
Beko AT3 Service Mode
TAURAS
TV
Service Mode
To enter the service mode, a special remote control which contains an additional SERVICE key must be used. See the illustration. Press the ‘SERVICE’ key on remote control, TV will display service menu as following table 1 line by line. To select the parameter by using the ‘P+/P-’ keys. To adjust the selected parameter by using the ‘V+/V-’ keys. To quit the service mode, press the ‘P.P.’ key on remote control when in the service mode.
DAEWOO
TV
Service Mode
Preset a station on 91 program
Press MENU
Select IMAGE
Set DEFINITION to 0
Quit
Press MENU
Select IMAGE
Press RED - GREEN - MENU
The options of service mode appear
TV
Service Mode
Service menu:
Switch-off tv.(mains switch)
Put the pin 7 of microprocessor to ground.(strap)
Power-on tv:a S appear in the left down corner.
Remove the strap of pin 7.
Press OSD (or RECALL) button on remote control.
Service adjustments
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Connect a jumper wire between terminals 3 (GND) and 6 (service) of connector TB on the Main PWB
4. Press the MODE button on the remote control
5. 'SERV' will appear on the screen
6. Remove the jumper wire
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Connect a jumper wire momentarily between terminals 2 (GND) and 6 (Service) of connector of CN1 on the Video
unit. Note that the wire is used just like a passing contact switch
5. 'SHARP Software Service Ver' will appear on the screen
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver off using the mains button
4. Press the volume down and channel up buttons on the front of the receiver at the same time
5. Keeping these buttons pressed, turn the mains on
6. When the set starts up it will be in service mode and SERVICE SOFTWARE will appear on the screen
7. Release the two buttons
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Turn the set off at the mains to exit the service mode.
Sharp
CTV
Service Mode
1. Connect a test pattern to the antenna terminal
2. Tune to this signal
3. Turn the receiver on
4. Press the service switch (S1401) located on the Video PWB
Use the channel up and down buttons to move between the options
Use the volume control buttons to change the data
Use the standby button on the remote control to store the data
Press the
Universal LED TV Service Mode
Most universal led tv boards check:
- Menu → 1147
- Menu → 2580
- Source → 2580
All LED TV Service Codes
- Menu → 1147
- Menu → 1185
- Menu → 1183
- Menu → 2580
- Menu → 1187
- Menu → 7050
- Menu → 8202
- Menu → 7343
- Menu → 2008
- Menu → 1999
- Menu → 0000
- Menu → 1167
- Menu → 1199
- Menu → 1234
- Menu → 2387
- Menu → 8893
- Menu → 2383
- Menu → 4725
- Source → 3138
- Source → 2580
- Source → 2585
- Source → 7342
- Source → 2583
- Source → 2283
- Source → 2285
- Source → 3195
- Source → 3137
- Source → 0000