| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | CDX5270 | TEST MODE ERROR CODES EXPLAINED (SEE CAR BULLETIN # 373) | Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode. | ||
| Sony | CDX5260 | TEST MODE ERROR CODES EXPLAINED (SEE CAR BULLETIN # 373) | Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode. | ||
| Sony | CDX5090 | REMOVING KEYSWITCHES (USE PYRO-PEN JR. ON SETTING # 1) | The keyswitches may be difficult to remove without damagingthe PCB. | ||
| Sony | CDX5090 | KEYSWITCHES FAIL | The keyswitches fail. It is most often the SELECT key butcould be any key. Sometimes there are more than 1 bad switch on the samefaceplate. -HQ COMMENTS: The QA group in Tokyo has been notified and samples havebeen sent to them. An improved switch ha | ||
| Sony | CDX5070 | TEST MODE ERROR CODES EXPLAINED (SEE CAR BULLETIN # 373) | Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode. | ||
| Sony | CDX5060 | TEST MODE ERROR CODES EXPLAINED (SEE CAR BULLETIN # 373) | Error codes which are not explained in the service manualsometimes appear on the display when operating the unit in the test mode. | ||
| Sony | CDX4090 | PAGES 39 - 42 MISSING FROM SERVICE MANUAL | CDX-4090 Srvice Manual. Four pages are missing: pages 39 -42. | ||
| Sony | CCDVX3 | MECH SCRAPING NOISE OR DRUM WON'T TURN/RPL SCREWS; SB CAM387 | Unit has propblem with excessive mechanical noise, ejectswithout tape in it or won't load tape, check to see whether or not thescrew that holds ref 164 loosens out. So far we had 2 units with samecomplaint. W33G4942 s/n1006109 W33g4203 s/n 1006500 | ||
| Sony | CCDV9 | EXCESS BRIGHTNESS AND NEGATIVE IMAGE IN EVF / NEW BOARDS | Excess brightness and negative image in EVF after installedthe new MCB ordered from NPC. Found resistors R908 R923 values reversed. -SOLUTION :Reinstalled R908/R923. EVF returned to normal. | ||
| Sony | CCDTRV70 | NO PICTURE IN THE LCD MONITOR / INSERT DATA INTO B0 TO BB | No picture in LCD monitor. | ||
| Sony | CCDTRV70 | NO EJECT/ DRUM RAMPS UP/ REPLACE X502 OFF OF IC505 | When powering up unit will spin the drum and stop. No otherfunctions work. After resoldering IC505 same problem. Isolated problemon servo board VC125, and found X502 not oscillating. | ||
| Sony | CCDTRV40 | NO PICTURE IN THE LCD MONITOR / INSERT DATA INTO B0 TO BB | No picture in LCD monitor. | ||
| Sony | CCDTRV40 | NO EJECT/ DRUM RAMPS UP/ REPLACE X502 OFF OF IC505 | When powering up unit will spin the drum and stop. No otherfunctions work. After resoldering IC505 same problem. Isolated problemon servo board VC125, and found X502 not oscillating. | ||
| Sony | CCDTRV30 | NO PICTURE IN THE LCD MONITOR / INSERT DATA INTO B0 TO BB | No picture in LCD monitor. | ||
| Sony | CCDTRV30 | NO EJECT/ DRUM RAMPS UP/ REPLACE X502 OFF OF IC505 | When powering up unit will spin the drum and stop. No otherfunctions work. After resoldering IC505 same problem. Isolated problemon servo board VC125, and found X502 not oscillating. |