Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
---|---|---|---|---|---|
Sony | SLV555UC | WON'T HIGH SPEED REWIND - OTHER FUNCTIONS OK | Unthreads and trys to high speed Rewind - then stops. Regularrewind operates ok all other functons operate ok. | ||
Sony | SPP170 | AVAILABILITY OF WALL MOUNTING BRACKETS | There is no mention of a wall mounting bracket in the servicemanual. | ||
Sony | SPP120 | AVAILABILITY OF WALL MOUNTING BRACKETS | There is no mention of a wall mounting bracket in the servicemanual. | ||
Sony | SPP115 | AVAILABILITY OF WALL MOUNTING BRACKETS | There are no mounting bracket part number in the servicemanual. | ||
Sony | CFD770 | UNIT DOES NOT KEEP TUNER PRESETS | Unit would not retain tuner presets when radio was turned off,or when mode was switched from radio to another mode. | ||
Sony | KPR46CX25 | SOUND OK - NO PICTURE - NO RASTER,REPLACED D-635 AND R-697 | Set had sound but no raster. No on screen display. Found novoltage on CRT filaments. | ||
Sony | SPP320 | INCORRECT PART NUMBER - ANTENNA DUPLEXER DPX1 | The part received from KCP is slightly larger than the one inthe unit. The dimension that causes a problem is the height the one fromKCP is too tall. The cabinet will not close as a result. This part isthe same one used in the SPP-100/110/150/300. I | ||
Sony | SPP170 | INCORRECT PART NUMBER - ANTENNA DUPLEXER DPX1 | The part received from KCP is slightly larger that the one inthe unit. The dimension that causes a problem is the height the one fromKCP is too tall. The cabinet will not close as a result. This part isthe same one used in the SPP-100/110/150/300. I | ||
Sony | SPP120 | INCORRECT PART NUMBER - ANTENNA DUPLEXER DPX1 | The part received from KCP is slightly larger than the one inthe unit. The dimension that causes a problem is the height the one fromKCP is too tall. The cabinet will not close as a result. This part isthe same one used in the SPP-100/110/150/300. I | ||
Sony | CPD1302 | AFTER WARM-UP, HIGH PITCH TONE | After a warm-up period of 15 to 30 minutes, internal noisewould be generated (1kHz range). Using an isolated tool, and touchingT-653 the noise would stop and then return. | ||
Sony | CPD1302 | VERTICAL SYNC PROBLEM | Unit came from independent service shop, they replaced IC-301on BA Brd and IC-206 on BD Brd. The vertical sync problem was notsolved (since they could not identify problem, unit was sent to us).Checked vertical sync at pin 9 on IC-206, ok. Checked pin | ||
Sony | KV27FX10 | INTERMITTENT LOSS OF VERTICAL DEFLECTION | Unit would intermittently manifest reduced vertical deflectionand foldover. After a while, it would lose vertical deflection altogetherwith a bright horizontal line showing at the center of the screen. Tracedproblem to bad solder connection between DY | ||
Sony | TCDD10 | POWER IS ON BUT NO LOADING | There is no tape loading after inserting the tape. | ||
Sony | TCW285 | CAPSTAN PART NUMBER | Need part number for capstan. -HQ COMMENTS: The part number is 3-390-806-11. This number wasacquired from the Service Manual for the TC-W200 because they havesimilar Mechanisms. A service bulletin will be generated with thisinformation. | ||
Sony | KV20TX10 | INTERMITTENT PICTURE, FBT | Picture would flash to black on heavy contrast scenes or whenpicture control was advanced. RGB output of IC-103 varying wildly.Output (pin 16) of PM-501 varying at same rate. Input (pin 9) of PM-501,same condition. Monitored ABL output of FBT pin 8 - |