| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | D25 | AUDIO MUTES AND DISPLAY GOES BLANK INTERMITTENTLY | Unit is intermittent and acts as though it was tapped veryhard. Sound mutes and time display goes away and comes back at the samepoint on the disc - no skipping. The spring becomes weak and the opticalblock cannot move forward because of the pressure o | ||
| Sony | D15 | AUDIO MUTES AND DISPLAY GOES BLANK INTERMITTENTLY | Unit is intermittent and acts as though it was tapped veryhard. Sound mutes and time display goes away and comes back at the samepoint on the disc - no skipping. The spring becomes weak and the opticalblock cannot move forward because of the pressure o | ||
| Sony | KV27HSR10 | DEAD, REPLACED FBT, R-571 AND Q-505 | The unit came in with a shorted HDT. A new replacement wasimmediately burnt out. | ||
| Sony | CFDW888 | UNIT SKIPS INTERMITTENTLY | New optic and old one have flex lead rubbing against bottom ofchassis plate. This causes skipping when sled motor moves. -HQ COMMENTS: Thanks for the info. Tokyo has been informed. | ||
| Sony | KV19TS20 | PICTURE DRIFTS, REPLACE Q-112 | Picture drifts and distorts. | ||
| Sony | KV27TS20 | PINCUSHION DISTORITION, D-519 | Pincushion distortion. | ||
| Sony | SPPS10 | NO AUDIO ON HANDSET | Handset audio board separates from the main circuit boardpulling the connection loose from the (audio) board. The audio board isnot available as a part, the entire main circuit board must be replaced. | ||
| Sony | DTC700 | NO DISPLAY | Unit had no -24 volts on CN-791. | ||
| Sony | KPR46CX10 | ON/OFF BUTTON PART NUMBER, MUST CHANGE FRONT BEZEL | Need the part number for the ON/OFF button. This button comesas part of the Bezel. It is very expensive to the customer to have toreplace the whole Bezel just for one button. -HQ COMMENTS: The buttons are not available nor, will they be made as arepl | ||
| Sony | TCWR11ES | SERVICE MANUAL DOES NOT EXIST | Need part number for wood side panels, but there is no servicemanual. -HQ COMMENTS: Use the service manual for the TCWR950, as it is virtuallyidentical to the TCWR11ES. A one-page manual for the TCWR11ES describesthe differences between it and the TCWR | ||
| Sony | KV32XBR10 | BAD SOLDER JOINTS AROUND T-501 HDT, RESOLDERED T-501 | Bad solder joint around T-501 HDT and unit had a bad H-outD-1941. | ||
| Sony | KV32XBR15 | NO PIX, OR SOUND, COLD SOLDER JOINT ON T-501 HDT, | Bad solder around T-501 HDT, caused the loss of Hor sweep andno raster resulted | ||
| Sony | TAM50 | INTERMITTENTLY MACHINE STOPS | Intermittently machine will not reset or sometimes stops inmiddle of ICM recording. At that time you will see (-) on display. Alsopertains to serial number 23638. | ||
| Sony | ITA850 | NO SOUND | Machine will automatically switch from OGM-A to OGM-B afterfirst ICM was recording. Headwire (HRP-701) is shorted (machine actinglike ICM tape is full) caused by IC-211 not in right position and touchingthe headwire. Thereby, shorting out the wire. | ||
| Sony | CDXA2001 | DISCS JAMMING IN THE XA-10B | Have received numerous complaints of discs jamming in XA-10B.Problem usually appears to be discs made off-spec (i.e. slightly thickerthan normal and having rough edges, so they fit too tight in XA-10B). Themost common brand of discs with this problem is |