| Marca | Modelo (Chassis) | Sintoma | Causa | Solução | Por: |
|---|---|---|---|---|---|
| Sony | SCD1020S | KEYBOARD DEAD OR WILL NOT TAKE KEY INPUT | Keyboard dead. Will not react to any key input. | ||
| Sony | SCD1020S | LOOPBACK TEST STOPS AUTOMATICALLY AFTER 1 TRANSMISSION | While in service mode and running a loopback test (TX/RXtest), the test will automatically stop after sending only 1 transmission(3 min). | ||
| Sony | SCD1020S | NO RECEIVE/SNA DOES TURN OFF/NO ERROR CODES | The keyboard's SATELLITE NOT AVAILABLE LED will turn offwhich means the receiver is locked and able to receive.However, the system will not receive any message even though SNA LED isoff and system is currently in service. No error codes are displayed. | ||
| Sony | SCD1020S | KEYBOARD LOSES POWER/DISPLAY WHEN BUMPED | When keyboard is bumped or exposed to vibration, the unitloses power/display and will restart itself back to self-diagnostics (start up routine). This is being caused by an intermittentconnection in the prom socket. This is due the nature of a LOCK IN | ||
| Sony | SCD1020S | KEYBOARD WILL NOT FUNCTION | The keyboard keys will not function. Unable to input specifickeys that stick. | ||
| Sony | SCD1020S | SYSTEM IS STUCK IN "SELF-DIAGNOSTICS" SCREEN | Upon powering system up, the keyboard normally displays self-diagnostics. After completion of self-diagnostics, the keyboard willdisplay the transmit menu. On these units, the system did not allow exitfrom the self-diagnostics screen and was stuck in t | ||
| Sony | CCDTR5 | INTERMITTENT LOADING AND EJECT | Unit would not always eject and load properly. | ||
| Sony | TCWR808M | CASSETTE DECK - NO OPERATION | Reset pin of IC-401 was never going high to 5 volts. Thisline was followed back to Q-402 and Q-401 which were measured with a DVM.Q-402 base was .1Vdc, however, Q-402 appeared to be on. Measuring thebase of Q-402 with an oscilloscope showed approximate | ||
| Sony | E92F19B160 | NO PART NUMBER LISTED FOR FRONT PANEL - REFERENCE NO. 101 | There is no part number listed on page 35 of the S/M for thefront panel (Ref. No. 101). -HQ COMMENTS: From W. Janowski/C. Rashi (Detroit SSC): P/N is1-464-753-11. This part includes the panel, all the buttons, and thedisplay PCB. Although it seems as i | ||
| Sony | SCD1020S | MISSING PART NUMBER ON RECEIVER CABLE | Both TX and RX antenna cables at antenna end have a protectiveboot that covers the end connector. When these cables are supplied withproduct, there is no problem. However, when supplied thru NPC Parts,there is a missing retainer ring on the RX cable. | ||
| Sony | KV27TS20 | SAP NOT WORKING, ALIGNMENT? | I was contacted by a customer because SAP didn't work on hisunit (we have weather on Channel 6, the PBS channel here). He went to thestore and the display model didn't work either. I went to another storeand the display didn't work on SAP either. -HQ | ||
| Sony | CDX6020 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled into the unit. It may also not beejected. The disc is engaged with the roller, but the roller is slippingon the shaft. | ||
| Sony | CDXR79 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled into the unit. It may also not beejected. The disc is engaged with the roller, but the roller is slippingon the shaft. | ||
| Sony | CDXR77 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled into the unit. It may also not beejected. The disc is engaged with the roller, but the roller is slippingon the shaft. | ||
| Sony | CDXA30 | WILL NOT LOAD DISC - ROLLER SLIPPING ON SHAFT | The disc will not be pulled out of the magazine. It will alsonot be pushed back in. The disc is engaged with the rollers, but theroller is slipping on the metal shaft. |